- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8023C-IMR (TERIDIAN SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, QCC32 PDF資料下載
參數資料
| 型號： | 73S8023C-IMR |
| 廠商： | TERIDIAN SEMICONDUCTOR CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 封裝： | 5 X 5 MM, QFN-32 |
| 文件頁數： | 3/27頁 |
| 文件大小： | 389K |
| 代理商： | 73S8023C-IMR |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
DS_8023C_019
73S8023C Data Sheet
Rev. 1.5
11
8
Activation and Deactivation
8.1
Activation Sequence (Synchronous Mode)
The 73S8023C smart card interface IC has an internal ~10 ms delay at power-on reset or on application
of VDD > VDDF
1.
CMDVCC is set low.
. No activation is allowed at this time.
CMDVCC (edge triggered) must then be set low to
activate the card.
The following steps list the activation sequence and the timing of the card control signals when the
system controller sets
CMDVCC low:
2.
Turn on VCC and I/O (AUX1, AUX2) to reception mode at the end of (tACT
3.
RST is a copy of
RSTIN and CLK is a copy of STROBE after (t
).
1).
Figure 3: Activation Sequence – Synchronous Mode
8.2
Deactivation Sequence (Synchronous Mode)
Deactivation is initiated either by the system controller by setting the
CMDVCC high, or automatically in
the event of hardware faults. Hardware faults are over-current, overheating, VDD
1.
RST goes low at time t
fault and card extraction
during the session and are indicated to the system controller by the fall of
OFF.
The following steps list the deactivation sequence and the timing of the card control signals when the
system controller sets the
CMDVCC high or a fault condition sets OFF low:
1
2.
CLK stops low at time t
.
2
3.
I/O goes low at time t
.
3
4.
V
. Out of reception mode.
CC is shut down at time t 4. After a delay t 5 (discharge of the V CC capacitor), VCC is low.
CMDVCC
VCC
IO
CLK
RSTIN
tACT
t1
RST
STROBE
tACT ~= 500s
t1 > 0.5s after tACT, RST = RSTIN, CLK = STROBE
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8023C-IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8024C-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8024C-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8024RN-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8024RN-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8023C-IMR/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8023C-IMR/F1 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8023C-IMR/F2 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8023C-IMR/F3 | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024C-DB | 功能描述:界面開發工具 73S8024C Demo Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。