- 您現在的位置：買賣IC網 > PDF目錄36330 > 935069850112 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PDIP52 PDF資料下載
參數資料
| 型號： | 935069850112 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP52 |
| 封裝： | 0.600 INCH, PLASTIC, SOT-247-1, SDIP-52 |
| 文件頁數： | 4/47頁 |
| 文件大小： | 250K |
| 代理商： | 935069850112 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
1996 Jan 26
12
Philips Semiconductors
Objective specication
I2C-bus controlled PAL/NTSC TV processors
TDA8376; TDA8376A
The output signal has an amplitude of approximately 2 V
black-to-white at nominal input signals and nominal
settings of the controls.
The black current stabilization is realized by feedback from
the video output amplifiers to the RGB control circuit. The
‘black current’ of the 3 guns of the picture tube is internally
measured and stabilized. The black level control is active
during 4 lines at the end of the vertical blanking. During the
first line the leakage current is measured and the following
3 lines the 3 guns are adjusted to the required level. The
maximum acceptable leakage current is
±100 A.
The nominal value of the ‘black current’ is 10
A. The ratio
of the currents for the various guns automatically tracks
with the white point adjustment so that the background
colour is the same as the adjusted white point.
The input impedance of the ‘black-current’ measuring pin
is 15 k
. Therefore the beam current during scan will
cause the input voltage to exceed the supply voltage. The
internal protection will start conducting so that the
excessive current is bypassed.
When the TV receiver is switched on the black current
stabilization circuit is not active, the RGB outputs are
blanked and beam current limiting input pin is
short-circuited. Only during the measuring lines will the
outputs supply a voltage of 5 V to the video output stage
so that it can be detected if the picture tube is warming up.
These pulses are switched on after a waiting time of
approximately 0.5 s. This ensures that the vertical
deflection is activated so that the measuring pulses are not
visible on the screen. As soon as the current supplied to
the measuring input exceeds a value of 190
A the
stabilization circuit is activated. After a waiting time of
approximately 0.8 s the blanking and the beam current
limiting input pin are released. The remaining switch-on
behaviour of the picture is determined by the external time
constant of the beam current limiting network.
8I2C-BUS SPECIFICATION
Valid subaddresses: 00 to 13 (TDA8376) or 00 to 16
(TDA8376A); subaddress FE is reserved for test
purposes. Auto-increment mode is available for
subaddresses.
8.1
Start-up procedure
Read the status bytes until POR = 0 and send all
subaddress bytes. The horizontal output signal is switched
on when the oscillator is calibrated.
Each time before the data in the IC is refreshed, the status
bytes must be read. If POR = 1, the procedure previously
mentioned must be carried out to restart the IC.
When this procedure is not followed the horizontal
frequency may be incorrect after power-up or after a
power dip.
handbook, halfpage
MLA743
A6
A5
A4
A3
A2
A1
A0
1
0
101
1/0
R/W
Fig.4 Slave address (8A).
相關PDF資料 |
PDF描述 |
|---|---|
| 935089530518 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 935071060157 | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| 935077580157 | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| 935206750518 | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| 935206750557 | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 93506EM8 | 制造商:undefined 功能描述: |
| 935079-000 | 制造商:TE Connectivity 功能描述:55A1841-16-MST4-9CS2275 - Cable Rools/Shrink Tubing |
| 935087-000 | 制造商:TE Connectivity 功能描述:301A511-51-05/164-0 - Bulk |
| 935087N001 | 制造商:TE Connectivity 功能描述:301A511-51-05/164-CS7092 制造商:TE Connectivity 功能描述:301A511-51-05/164-CS7092 - Bulk |
| 9350DC-200-0GZZZA | 制造商:Siemens 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。