- 您現在的位置：買賣IC網 > PDF目錄36332 > 935224710112 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PDIP56 PDF資料下載
參數資料
| 型號： | 935224710112 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP56 |
| 封裝： | 0.600 INCH, PLASTIC, SOT-400, SDIP-56 |
| 文件頁數： | 36/75頁 |
| 文件大小： | 522K |
| 代理商： | 935224710112 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁
1997 Jul 01
41
Philips Semiconductors
Preliminary specication
I2C-bus controlled economy PAL/NTSC
and NTSC TV-processors
TDA837x family
7. Measured in accordance with the test line given in Fig.14. For the differential phase test the peak white setting is
reduced to 87%.
a) The differential gain is expressed as a percentage of the difference in peak amplitudes between the largest and
smallest value relative to the subcarrier amplitude at blanking level.
b) The phase difference is defined as the difference in degrees between the largest and smallest phase angle.
8. This figure is valid for the complete video signal amplitude (peak white-to-black), see Fig.15.
9. The noise inverter is only active in the ‘strong signal mode’ (no noise detected in the incoming signal).
10. The test set-up and input conditions are given in Fig.16. The figures are measured with an input signal of
10 mV (RMS).
11. Measured with a source impedance of 75
, where:
12. The AGC response time is also dependent on the acquisition time of the PLL demodulator. The values given are valid
when the PLL is in lock.
13. The AFC control voltage is obtained from the control voltage of the VCO of the PLL demodulator. The tuning
information is supplied to the tuning system via the I2C-bus. Two bits are reserved for this function. The AFC value
is valid only when the SL bit = 1.
14. Vi = 100 mV (RMS), FM: 1 kHz, f= ±50 kHz.
15. Vi = 50 mV (RMS), f = 4.5 to 5.5 MHz; FM: 70 Hz, ±50 kHz deviation; AM: 1 kHz, 30% modulation.
16. The Automatic Volume Levelling (AVL) circuit automatically stabilizes the audio output signal to a certain level which
can be set by means of the volume control. This AVL function prevents big audio output fluctuations due to variation
of the modulation depth of the transmitter. The AVL can be switched on and off via the I2C-bus.
For the TDA8373 the AVL is active over an input voltage range (measured at the de-emphasis output) between
75 and 750 mV (RMS). For the TDA8374 this input level is dependent on the crystals which are connected to the
colour decoder. When only 3.5 MHz crystals are connected (indicated via the XA/XB bits) the active input level is
identical to that of the TDA8373. When a 4.4 MHz crystal is connected the input signal range is increased to
150 to 1500 mV (RMS), this to cope with the larger FM swing of European transmitters.
The AVL control curve for the 2 standards is given in Fig.29 and Fig.30. The control range of +6 to
14 dB is valid
for input signals with 50% of the maximum frequency deviation.
17. Vi = 100 mV (RMS), f = 5.5 MHz; FM: 1 kHz, ±17.5 kHz deviation, 15 kHz bandwidth; audio attenuator at 6 dB.
18. Vi = 100 mV (RMS), f = 4.5 to 5.5 MHz, FM: 1 kHz, ±100 kHz deviation.
19. Unweighted RMS value, Vi = 100 mV (RMS), FM: 1 kHz, ±50 kHz deviation, volume control: 6 dB.
20. Audio attenuator at
20 dB; temperature range = 10 to 50 °C.
21. Signal with negative-going sync. Amplitude includes sync pulse amplitude.
22. This parameter is measured at nominal settings of the various controls.
23. Indicated as a signal for a colour bar with 75% saturation (chroma-to-burst ratio = 2.2 : 1).
24. Nominal contrast is specified with the DAC in position 20H. Nominal saturation as maximum
10 dB. At nominal
settings of brightness and white point the black level at the outputs is 300 mV lower than the level of the black current
measuring pulses.
25. The luminance output and input of the TDA8375A, TDA8377A, TDA8375 and TDA8377 can be connected directly.
When additional picture improvement ICs (such as the TDA9170) are applied the inputs of these ICs must be
AC-coupled because of the black level clamp requirement. The output of the picture improvement ICs can be directly
coupled to the luminance input as long as the DC level of the signal has a value between 1 and 7 V.
To be able to apply CTI ICs such as the TDA4565 and TDA4566 the gain of the luminance channel can be increased
via the setting of the GAI bit in the I2C-bus subaddress 03.
S/N = 20 log
V
O(b-w)
V
m rms
() B =5MHz
()
---------------------------------------------------------
相關PDF資料 |
PDF描述 |
|---|---|
| 935224740112 | SPECIALTY CONSUMER CIRCUIT, PDIP56 |
| 935224770551 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 935224770557 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 935224780112 | SPECIALTY CONSUMER CIRCUIT, PDIP56 |
| 935196680112 | SPECIALTY CONSUMER CIRCUIT, PDIP52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 9352370001 | 功能描述:HEAT SHRINK SLEEVE RoHS:是 類別:線纜，導線 - 管理 >> 標簽，標記 系列:HT-SCE 標準包裝:250 系列:CM-SCE 標簽類型:標準 標簽尺寸:2.00" x 0.25"（50.8mm x 6.4mm） 顏色:白 材質:聚烯烴 適用于相關產品:點陣打印機 包裝:* 工作溫度:-55°C ~ 135°C 其它名稱:A105291CM-SCE-TP-1/4-4H-9 |
| 935241-0001 | 制造商: 功能描述: 制造商:DIGITRAN 功能描述: 制造商:undefined 功能描述: |
| 935241-1 | 制造商:DIGITRAN 功能描述: 制造商:DTRAN 功能描述: |
| 935245650125 | 制造商:NXP Semiconductors 功能描述:Inverter 1-Element CMOS 5-Pin TSSOP T/R |
| 935248-90 | 制造商:JANCO 功能描述:935248-90 |
發布緊急采購，3分鐘左右您將得到回復。