參數資料
| 型號： | 9882 1 IN X 36 YD |
| 廠商： | 3M |
| 文件頁數： | 3/5頁 |
| 文件大?。?/td> | 0K |
| 描述： | THERM COND ADH 2.0MIL 1"X36YD |
| 特色產品： | Thermal Interface Materials |
| 標準包裝： | 9 |
| 類型： | 丙烯酸粘合劑 |
| 尺寸/尺寸： | 1.00" W x 36 yd 卷 |
| 其它名稱： | 3M9590 70006178910 |
3M
Thermally Conductive Adhesive Transfer Tapes
9882
9885 9890
Application Guidelines
1.) Substrate surfaces should be clean and dry prior to tape application. Isopropyl alcohol (isopropanol) applied with a lint-
free wipe or swab should be adequate for removing surface contamination such as dust or finger prints. Do not use
“denatured alcohol” or glass cleaners, which often contain oily components. Allow the surface to dry for several
minutes before applying the tape. More aggressive solvents (such as acetone, methyl ethyl ketone [MEK] or toluene)
may be required to remove heavier contamination (grease, machine oils, solder flux, etc.) but should be followed by a
final isopropanol wipe as described above.
Note: Be sure to read and follow the manufacturers’ precautions and directions when using primers and solvents.
2.) Apply the tape to one substrate at a modest angle with the use of a squeegee, rubber roller or finger pressure to help
reduce the potential for air entrapment under the tape during its application. The liner can be removed after positioning
the tape onto the first substrate.
3) Assemble the part by applying compression to the substrates to ensure a good wetting of the substrate surfaces with the
tape. Proper application of pressure (amount of pressure, time applied, temperature applied) will depend upon design of
the parts. Rigid substrates are more difficult to bond without air entrapment as most rigid parts are not flat. Use of a
thicker tape may result in increased wetting of rigid substrates. Flexible substrates can be bonded to rigid or flexible
parts with much less concern about air entrapment because one of the flexible substrate can conform to the other
substrates.
4.) Application pressure guideline table for 3M Thermally Conductive Adhesive Transfer Tapes 9882, 9885, and 9890.
Substrate
Application Conditions
Time
Rigid to rigid
Minimum: 15 psi at room temperature
2 sec
Preferred: 50 psi at room temperature
5 sec
More pressure equals better wetting
Flexible to rigid
Minimum: 5 psi at room temperature
1 sec
Preferred: 15 psi at room temperature
5 sec
Flexible to flexible
Minimum: 5 psi at room temperature
1 sec
Preferred: 15 psi at room temperature
5 sec
5.) Application Tips:
For rigid to rigid bonding, a twisting motion during assembly of the substrates will improve wetting. This should be a
back and forth twisting motion during the application of compression.
For flexible to rigid or flexible to flexible bonding, a roll lamination system may be employed to apply the flexible
substrate down to the rigid (or other flexible) substrate. Rubber nip rollers, heated steel rollers, and other methods can be
employed to bond in a continuous manner.
Heat can be employed to increase wetting percentage and wetting rate of the substrates and to build room temperature
bond strength.
Primers may be employed to increase adhesion to low surface energy substrates (eg. plastic packages). Contact your
3M representative for more information about primers.
For best product performance, it is important to use pressure and time conditions to achieve as much wetting as possible.
(3)
相關PDF資料 |
PDF描述 |
|---|---|
| 77063473P | RES ARRAY 47K OHM 3 RES 6-SIP |
| PMS-04V-S | CONN RETAINER PA 4POS 2MM |
| 77063331P | RES ARRAY 330 OHM 3 RES 6-SIP |
| 77063223P | RES ARRAY 22K OHM 3 RES 6-SIP |
| 145602040000829+ | CONN PLUG BD/BD 40POS .4MM SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 98822 | 制造商:IXYS 制造商全稱:IXYS Corporation 功能描述:High Voltage MOSFET |
| 9882-2000 | 功能描述:近程傳感器 OBPL-B05-S360-1030VDC;200mA-PNP-NO-2m RoHS:否 制造商:Vishay Semiconductors 感應方式:Optical 感應距離:1 mm to 200 mm 電源電壓:2.5 V to 3.6 V 安裝風格:SMD/SMT 輸出配置:Digital 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 系列:VCNL3020 |
| 988221020 | 制造商:Molex 功能描述: |
| 98822-1020 | 功能描述:汽車連接器 PIN CONN 1.5 2CKT WHITE RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel |
| 988221021 | 制造商:Molex 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。