- 您現在的位置：買賣IC網 > PDF目錄164964 > A1361LKTTN-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.65-4.80V, RECTANGULAR, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | A1361LKTTN-T |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.65-4.80V, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | LEAD FREE, PLASTIC, SIP-4 |
| 文件頁數： | 7/25頁 |
| 文件大小： | 615K |
| 代理商： | A1361LKTTN-T |
A1360, A1361,
and A1362
Programming Pulse Requirements, protocol at TA = 25°C
Characteristic
Symbol
Notes
Min.
Typ.
Max.
Units
Programming Voltage
VP(LOW)
Measured at the VOUT pin.
–
5.5
V
VP(MID)
14
15
16
V
VP(HIGH)
26
27
28
V
Programming Current
IP
Minimum supply current required to ensure proper
fuse blowing. In addition, a minimum capacitance,
CBLOW = 0.1 μF, must be connected between the
VOUT and GND pins during programming, to provide
the current necessary for fuse blowing.
300
–
mA
Pulse Width
tLOW
Duration of VP(LOW) voltage level for separating
VP(MID) and VP(HIGH) pulses, and delay time after the
final VBLOW pulse.
40
–
μs
tACTIVE
Duration of VP(MID) and VP(HIGH) pulses for register
selection or bit field addressing.
40
–
μs
tBLOW
Duration of VP(HIGH) pulses for fuse blowing.
40
–
μs
Pulse Rise Time
tPr
Rise time required for transitions from VP(LOW) to
either VP(MID) or VP(HIGH).
5
–
100
μs
Pulse Fall Time
tPf
Fall time required for transitions from VP(HIGH) or
VP(MID) to VP(LOW).
5
–
100
μs
Zone The 136x programming logic is designed to accept up to
two different key-code combinations sequentially without cycling
the supply. The first key-code combination is interpreted as
addressing a register in the first zone, and the second key-code
combination is interpreted as addressing a register in the second
zone. All of the parameter registers are located in either the first
or second zone. The first zone must be entered and exited before
the parameter registers available in the second zone may be
accessed.
Fuse Blowing Applying a high voltage pulse of sufficient dura-
tion to permanently set an addressed bit by blowing a fuse
internal to the device. After a bit (fuse) has been blown, it cannot
be reset.
Blow Pulse A high voltage pulse of sufficient duration to blow the
addressed fuse.
Cycling the Supply Powering-down, and then powering-up the
supply voltage. Cycling the supply is used to clear the program-
ming settings in Try mode.
Low-Noise Programmable Linear Hall Effect Sensor ICs with
Adjustable Bandwidth (50 kHz Maximum) and Analog Output
15
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相關PDF資料 |
PDF描述 |
|---|---|
| A150N50X4A | 0 MHz - 2700 MHz 50 ohm RF/MICROWAVE TERMINATION |
| A15QS1-2 | FAST BLOW ELECTRIC FUSE, 1A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS10-2 | FAST BLOW ELECTRIC FUSE, 10A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS100-4TI | FAST BLOW ELECTRIC FUSE, 100A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS100-4 | FAST BLOW ELECTRIC FUSE, 100A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1362LKTTN-T | 功能描述:IC HALL EFFECT SENSOR LN 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1363LKTTN-10-T | 功能描述:IC HALL SENSOR 6.4-14MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
| A1363LKTTN-1-T | 功能描述:IC HALL SENSOR 0.6-1.3MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:模塊 標準包裝:1 |
| A1363LKTTN-2-T | 功能描述:IC HALL SENSOR 1.3-2.9MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
| A1363LKTTN-5-T | 功能描述:IC HALL SENSOR 2.9-6.4MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。