欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： A40MX04-PL68M
元件分類： FPGA
英文描述： FPGA, 547 CLBS, 6000 GATES, 80 MHz, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 107/124頁
文件大?。?/td> 3142K
代理商： A40MX04-PL68M
40MX and 42MX FPGA Families
v6.1
1-77
Pin Descriptions
CLK/A/B, I/O
Global Clock
Clock inputs for clock distribution networks. CLK is for
40MX while CLKA and CLKB are for 42MX devices. The
clock input is buffered prior to clocking the logic
modules. This pin can also be used as an I/O.
DCLK, I/O
Diagnostic Clock
Clock
input
for
diagnostic
probe
and
device
programming. DCLK is active when the MODE pin is
HIGH. This pin functions as an I/O when the MODE pin is
LOW.
GND
Ground
Input LOW supply voltage.
I/O
Input/Output
Input, output, tristate or bi-directional buffer. Input and
output levels are compatible with standard TTL and
CMOS specifications. Unused I/Os pins are configured by
the Designer software as shown in Table 40.
In all cases, it is recommended to tie all unused MX I/O
pins to LOW on the board. This applies to all dual-
purpose pins when configured as I/Os as well.
LP
Low Power Mode
Controls the low power mode of all 42MX devices. The
device is placed in the low power mode by connecting
the LP pin to logic HIGH. In low power mode, all I/Os are
tristated, all input buffers are turned OFF, and the core
of the device is turned OFF. To exit the low power mode,
the LP pin must be set LOW. The device enters the low
power mode 800ns after the LP pin is driven to a logic
HIGH. It will resume normal operation in 200s after the
LP pin is driven to a logic LOW.
MODE
Mode
Controls the use of multifunction pins (DCLK, PRA, PRB,
SDI, TDO). The MODE pin is held HIGH to provide
verification
capability.
The
MODE
pin
should
be
terminated to GND through a 10k
Ω resistor so that the
MODE pin can be pulled HIGH when required.
NC
No Connection
This pin is not connected to circuitry within the device.
These pins can be driven to any voltage or can be left
floating with no effect on the operation of the device.
PRA, I/O
PRB, I/O
Probe A/B
The Probe pin is used to output data from any user-
defined design node within the device. Each diagnostic
pin can be used in conjunction with the other probe pin
to allow real-time diagnostic output of any signal path
within the device. The Probe pin can be used as a user-
defined I/O when verification has been completed. The
pin's probe capabilities can be permanently disabled to
protect programmed design confidentiality. The Probe
pin is accessible when the MODE pin is HIGH. This pin
functions as an I/O when the MODE pin is LOW.
QCLKA/B/C/D, I/O
Quadrant Clock
Quadrant clock inputs for A42MX36 devices. When not
used as a register control signal, these pins can function
as user I/Os.
SDI, I/O
Serial Data Input
Serial data input for diagnostic probe and device
programming. SDI is active when the MODE pin is HIGH.
This pin functions as an I/O when the MODE pin is LOW.
SDO, I/O
Serial Data Output
Serial data output for diagnostic probe and device
programming. SDO is active when the MODE pin is HIGH.
This pin functions as an I/O when the MODE pin is LOW.
SDO is available for 42MX devices only.
When Silicon Explorer II is being used, SDO will act as an
output while the "checksum" command is run. It will
return to user I/O when "checksum" is complete.
TCK, I/O
Test Clock
Clock signal to shift the Boundary Scan Test (BST) data
into the device. This pin functions as an I/O when
"Reserve JTAG" is not checked in the Designer Software.
BST pins are only available in A42MX24 and A42MX36
devices.
TDI, I/O
Test Data In
Serial data input for BST instructions and data. Data is
shifted in on the rising edge of TCK. This pin functions as
an I/O when "Reserve JTAG" is not checked in the
Designer Software. BST pins are only available in
A42MX24 and A42MX36 devices.
TDO, I/O
Test Data Out
Serial data output for BST instructions and test data. This
pin functions as an I/O when "Reserve JTAG" is not
checked in the Designer Software. BST pins are only
available in A42MX24 and A42MX36 devices.
Table 40
Configuration of Unused I/Os
Device
Configuration
A40MX02, A40MX04
Pulled LOW
A42MX09, A42MX16
Pulled LOW
A42MX24, A42MX36
Tristated
相關PDF資料
PDF描述
A40MX04-PL68X79 FPGA, 547 CLBS, 6000 GATES, 80 MHz, PQCC68
A40MX04-PL68 FPGA, 547 CLBS, 6000 GATES, 80 MHz, PQCC68
A40MX04-PL84AX79 FPGA, 547 CLBS, 6000 GATES, 116 MHz, PQCC84
A40MX04-PL84A FPGA, 547 CLBS, 6000 GATES, 116 MHz, PQCC84
A40MX04-PL84IX79 FPGA, 547 CLBS, 6000 GATES, 80 MHz, PQCC84
相關代理商/技術參數
參數描述
A40MX04-PL68X4 制造商:Microsemi Corporation 功能描述:MX SERIES 6000 GATES FPGA
A40MX04-PL84 功能描述:IC FPGA MX SGL CHIP 6K 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:MX 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17）
A40MX04-PL84A 功能描述:IC FPGA MX SGL CHIP 6K 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:MX 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17）
A40MX04-PL84I 功能描述:IC FPGA MX SGL CHIP 6K 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:MX 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17）
A40MX04-PL84M 制造商:Microsemi Corporation 功能描述:FPGA 6K GATES 547 CELLS 83MHZ/139MHZ 0.45UM 3.3V/5V 84PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:IC FPGA 69 I/O 84PLCC 制造商:Microsemi Corporation 功能描述:IC FPGA MX SGL CHIP 6K 84-PLCC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 义马市| 连山| 安泽县| 晋江市| 凭祥市| 牟定县| SHOW| 平阳县| 桦甸市| 阳泉市| 清镇市| 重庆市| 沾化县| 黎川县| 清徐县| 梧州市| 仙居县| 福贡县| 德化县| 长沙县| 班玛县| 苗栗县| 东辽县| 韶关市| 大关县| 大庆市| 茌平县| 竹山县| 汝南县| 钟山县| 常宁市| 永修县| 从化市| 三明市| 岢岚县| 天柱县| 金堂县| 深圳市| 天津市| 富顺县| 杭锦后旗|