- 您現在的位置：買賣IC網 > PDF目錄373927 > AD7687 (Analog Devices, Inc.) +3.3V, 2.7Gbps Dual 2 x 2 Crosspoint Switch PDF資料下載
參數資料
| 型號： | AD7687 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | +3.3V, 2.7Gbps Dual 2 x 2 Crosspoint Switch |
| 中文描述： | 3MW的，100ksps的14位ADC的6引腳SOT - 23 |
| 文件頁數： | 13/20頁 |
| 文件大小： | 480K |
| 代理商： | AD7687 |
AD7940
MODES OF OPERATION
The mode of operation of the AD7940 is selected by controlling
the (logic) state of the CS signal during a conversion. There are
two possible modes of operation, normal and power-down. The
point at which CS is pulled high after the conversion has been
initiated will determine whether or not the AD7940 will enter
power-down mode. Similarly, if already in power-down, CS can
control whether the device will return to normal operation or
remain in power-down. These modes of operation are designed
to provide flexible power management options. These options
can optimize the power dissipation/throughput rate ratio for
differing application requirements.
Rev. 0 | Page 13 of 20
NORMAL MODE
This mode provides the fastest throughput rate performance
because the user does not have to worry about the power-up
times with the AD7940 remaining fully powered all the time.
Figure 16 shows the general diagram of the operation of the
AD7940 in this mode.
The conversion is initiated on the falling edge of CS as
described in the Serial Interface section. To ensure that the part
remains fully powered up at all times, CS must remain low until
at least 10 SCLK falling edges have elapsed after the falling edge
of CS. If CS is brought high any time after the 10th SCLK falling
edge, but before the 16th SCLK falling edge, the part will remain
powered up, but the conversion will be terminated and SDATA
will go back into three-state. At least 16 serial clock cycles are
required to complete the conversion and access the complete
conversion result. CS may idle high until the next conversion or
may idle low until CS returns high sometime prior to the next
conversion, effectively idling CS low.
Once a data transfer is complete (SDATA has returned to three-
state), another conversion can be initiated after the quiet time,
t
QUIET
, has elapsed by bringing CS low again.
0
1
12
1 LEADING ZERO + CONVERSION RESULT
CS
SCLK
16
SDATA
Figure 16. Normal Mode Operation
相關PDF資料 |
PDF描述 |
|---|---|
| AD7683ARM | 16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| AD7683ARMRL7 | 16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| AD7683BRM | 16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| AD7940 | 3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
| AD7683BRMRL7 | 16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD76871 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7687BCPZ-R2 | 制造商:Analog Devices 功能描述: |
| AD7687BCPZRL | 功能描述:IC ADC 16BIT SAR 250KSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7687BCPZRL7 | 功能描述:IC ADC 16BIT SAR 250KSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7687BRM | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 16-bit Serial 10-Pin MSOP Tube 制造商:Analog Devices 功能描述:IC 16-BIT ADC |
發布緊急采購，3分鐘左右您將得到回復。