- 您現在的位置：買賣IC網 > PDF目錄373914 > AD7715ARU-5 (ANALOG DEVICES INC) AB 4C 4#12 PIN RECP PDF資料下載
參數資料
| 型號： | AD7715ARU-5 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | AB 4C 4#12 PIN RECP |
| 中文描述： | 1-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | MO-153AB, TSSOP-16 |
| 文件頁數： | 16/31頁 |
| 文件大小： | 474K |
| 代理商： | AD7715ARU-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
REV. C
AD7715
–16–
DIGITAL FILTERING
The AD7715 contains an on-chip low-pass digital filter that
processes the output of the part’s sigma-delta modulator. There-
fore, the part not only provides the analog-to-digital conversion
function but it also provides a level of filtering. There are a
number of system differences when the filtering function is
provided in the digital domain rather than the analog domain
and the user should be aware of these.
First, since digital filtering occurs after the A-to-D conversion
process, it can remove noise injected during the conversion
process. Analog filtering cannot do this. Also, the digital filter
can be made programmable far more readily than an analog
filter. Depending on the digital filter design, this gives the user
the capability of programming cutoff frequency and output
update rate.
On the other hand, analog filtering can remove noise superim-
posed on the analog signal before it reaches the ADC. Digital
filtering cannot do this and noise peaks riding on signals near
full scale have the potential to saturate the analog modulator
and digital filter, even though the average value of the signal is
within limits. To alleviate this problem, the AD7715 has over-
range headroom built into the sigma-delta modulator and digital
filter which allows overrange excursions of 5% above the analog
input range. If noise signals are larger than this, consideration
should be given to analog input filtering, or to reducing the
input channel voltage so that its full scale is half that of the
analog input channel full scale. This will provide an overrange
capability greater than 100% at the expense of reducing the
dynamic range by 1 bit (50%).
In addition, the digital filter does not provide any rejection at
integer multiples of the digital filter’s sample frequency. How-
ever, the input sampling on the part provides attenuation at
multiples of the digital filter’s sampling frequency so that the
unattenu-ated bands actually occur around multiples of the
sampling frequency f
S
(as defined in Table XV). Thus the unat-
tenuated bands occur at n
×
f
S
(where n = 1, 2, 3. . . ). At these
frequencies, there are frequency bands,
±
f
3 dB
wide (f
3 dB
is the
cutoff frequency of the digital filter) at either side where noise
passes unattenuated to the output.
Filter Characteristics
The AD7715’s digital filter is a low-pass filter with a (sinx/x)
3
response (also called sinc
3
). The transfer function for this filter
is described in the z-domain by:
1
and in the frequency domain by:
where
N
is the ratio of the modulator rate to the output rate and
f
MOD
is the modulator rate.
with a gain of 2 and a V
REF
of +2.5V, the input voltage range
on the AIN(+) input is +2.5V to +3.75V. If AIN(–) is +2.5V
and the AD7715 is configured for bipolar mode with a gain of 2
and a V
REF
of +2.5V, the analog input range on the AIN(+)
input is +1.25V to +3.75 V (i.e., 2.5V
±
1.25V). If AIN(–) is
at AGND, the part cannot be configured for bipolar ranges in
excess of
±
30mV.
Bipolar or unipolar options are chosen by programming the
B
/U
bit of the Setup Register. This programs the channel for either
unipolar or bipolar operation. Programming the channel for
either unipolar or bipolar operation does not change any of the
input signal conditioning; it simply changes the data output
coding and the points on the transfer function where calibra-
tions occur.
REFERENCE INPUT
The AD7715’s reference inputs, REFIN(+) and REFIN(–),
provide a differential reference input capability. The common-
mode range for these differential inputs is from AGND to
AV
DD
. The nominal reference voltage, V
REF
(REFIN(+)–
REFIN(–)), for specified operation is +2.5V for the AD7715-5
and +1.25V for the AD7715-3. The part is functional with
V
REF
voltages down to 1 V but with degraded performance as
the output noise will, in terms of LSB size, be larger. REFIN(+)
must always be greater than REFIN(–) for correct operation of
the AD7715.
Both reference inputs provide a high impedance, dynamic load
similar to the analog inputs in unbuffered mode. The maximum
dc input leakage current is
±
1 nA over temperature and source
resistance may result in gain errors on the part. In this case, the
sampling switch resistance is 5k
typ and the reference capaci-
tor (C
REF
) varies with gain. The sample rate on the reference
inputs is f
CLK IN
/64 and does not vary with gain. For gains of 1
and 2, C
REF
is 8pF; for a gain of 32, it is 4.25pF, and for a gain
of 128, it is 3.3125pF.
The output noise performance outlined in Tables V through XII
is for an analog input of 0V which effectively removes the effect
of noise on the reference. To obtain the same noise performance
as shown in the noise tables over the full input range requires a
low noise reference source for the AD7715. If the reference
noise in the bandwidth of interest is excessive, it will degrade
the performance of the AD7715. In applications where the
excitation voltage for the bridge transducer on the analog input
also derives the reference voltage for the part, the effect of the
noise in the excitation voltage will be removed as the application
is ratiometric. Recommended reference voltage sources for the
AD7715-5 include the AD780, REF43 and REF192, while the
recommended reference sources for the AD7715-3 include the
AD589 and AD1580. It is generally recommended to decouple
the output of these references in order to further reduce the
noise level.
H( )
N
z
z
N
–
–
–
=
×
1
1
1
3
| ( )|
H f
N
Sin N
f
f
Sin
f
f
s
s
=
×
× ×
π
×
1
3
π
相關PDF資料 |
PDF描述 |
|---|---|
| AD7715AN-3 | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| AD7715AN-5 | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| AD7715AR-3 | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| AD7715AR-5 | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| AD7715* | 3 V/5 V. 450 uA 16-Bit. Sigma-Delta ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7715ARU-5REEL | 功能描述:IC ADC 16BIT SIGMA-DELTA 16TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7715ARU-5REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 19.2ksps 16-bit Serial 16-Pin TSSOP T/R |
| AD7715ARUZ-3 | 功能描述:IC ADC 16BIT SIGMA-DELTA 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7715ARUZ-31 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 450 ??A 16-Bit, Sigma-Delta ADC |
| AD7715ARUZ-3REEL7 | 功能描述:IC ADC 16BIT SIGMA-DELTA 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。