- 您現在的位置：買賣IC網 > PDF目錄373919 > AD7849AR (ANALOG DEVICES INC) Serial Input, 14-Bit/16-Bit DAC PDF資料下載
參數資料
| 型號： | AD7849AR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | Serial Input, 14-Bit/16-Bit DAC |
| 中文描述： | SERIAL INPUT LOADING, 7 us SETTLING TIME, 14-BIT DAC, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 8/15頁 |
| 文件大小： | 211K |
| 代理商： | AD7849AR |
REV. B
–
8
–
AD7849
LOGIC
CIRCUITRY
ONE-SHOT
LDAC
DAC 3
G3
C1
R
10k
R
OFS
RSTIN
G1
V
OUT
AGND
RSTOUT
G2
R
10k
VOLTAGE
MONITOR
Figure 11. AD7849 Output Stage
When the supply voltages are changing, the V
OUT
pin is clamped
to 0 V via a low impedance path . To prevent the output of A3
being shorted to 0 V during this time, transmission gate G1 is
also opened. These conditions are maintained until the power
supplies stabilize and a valid word is written to the DAC regis-
ter. At this time, G2 opens and G1 closes. Both transmission
gates are also externally controllable via the Reset In (
RST IN
)
control input. For instance, if the
RST IN
input is driven from a
battery supervisor chip, then on power-off or during a brown-
out, the
RST IN
input will be driven low to open G1 and close
G2. The DAC has to be reloaded, with
RST IN
high, to re-en-
able the output. Conversely, the on-chip voltage detector out-
put (
RST OUT
) is also available to the user to control other
parts of the system.
The AD7849 output buffer is configured as a track-and-hold
amplifier. Although normally tracking its input, this amplifier is
placed in a hold mode for approximately 5
μ
s after the leading
edge of
LDAC
. This short state keeps the DAC output at its
previous voltage while the AD7849 is internally changing to its
new value. So, any glitches that occur in the transition are not
seen at the output. In systems where the
LDAC
is permanently
low, the deglitching will not be in operation.
CIRCUIT DESCRIPTION
D/A CONVERSION
Figure 10 shows the D/A section of the AD7849. There are
three on-chip DACs each of which has its own buffer amplifier.
DAC1 and DAC2 are 4-bit DACs. They share a 16-resistor
string but have their own analog multiplexers. The voltage ref-
erence is applied to the resistor string. DAC3 is a 12-bit voltage
mode DAC with its own output stage.
The 4 MSBs of the 16-bit digital input code drive DAC1 and
DAC2 while the 12 LSBs control DAC3. Using DAC1 and
DAC2, the MSBs select a pair of adjacent nodes on the resistor
string and present that voltage to the positive and negative
inputs of DAC3. This DAC interpolates between these two
voltages to produce the analog output voltage.
To prevent nonmonotonicity in the DAC due to amplifier offset
voltages, DAC1 and DAC2 “l(fā)eap-frog” along the resistor string.
For example, when switching from Segment 1 to Segment 2,
DAC1 switches from the bottom of Segment 1 to the top of
Segment 2 while DAC 2 remains connected to the top of Seg-
ment 1. The code driving DAC3 is automatically comple-
mented to compensate for the inversion of its inputs. This
means that any linearity effects due to amplifier offset voltages
remain unchanged when switching from one segment to the
next and 16-bit monotonicity is ensured if DAC3 is monotonic.
So, 12-bit resistor matching in DAC3 guarantees overall 16-bit
monotonicity. This is much more achievable than the 16-bit
matching which a conventional R-2R structure would have
needed.
Output Stage
The output stage of the AD7849 is shown in Figure 11. It is ca-
pable of driving a load of 2 k
in parallel with 200 pF. The
feedback and offset resistors allow the output stage to be config-
ured for gains of 1 or 2. Additionally, the offset resistor may be
used to shift the output range.
The AD7849 has a special feature to ensure output stability
during power-up and power-down sequences. This is specifi-
cally available for control applications where actuators must not
be allowed to move in an uncontrolled fashion.
10/12
DB15
–
DB12
DAC 2
A1
A2
DAC 3
10-BIT/12-BIT
DAC
S2
S4
S14
S16
DB15
–
DB12
DAC 1
S1
S3
S15
S17
V
REF+
V
REF
–
OUTPUT
STAGE
R
R
R
R
R
R
Figure 10. AD7849 D/A Conversion
相關PDF資料 |
PDF描述 |
|---|---|
| AD7849BN | Serial Input, 14-Bit/16-Bit DAC |
| AD7849BR | Serial Input, 14-Bit/16-Bit DAC |
| AD7849CN | Serial Input, 14-Bit/16-Bit DAC |
| AD7849CR | Serial Input, 14-Bit/16-Bit DAC |
| AD7849TQ | Serial Input, 14-Bit/16-Bit DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7849AR-REEL | 功能描述:IC DAC 16BIT SRL INP 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| AD7849ARZ | 功能描述:IC DAC 14/16BIT SRL-IN 20-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD7849ARZ-REEL | 功能描述:IC DAC 14/16BIT SRL-IN 20-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD7849BN | 制造商:Analog Devices 功能描述:DAC 1-CH R-2R 16-bit 20-Pin PDIP N Tube 制造商:Rochester Electronics LLC 功能描述:SERIAL INPUT,16-BIT DAC I.C. - Bulk |
| AD7849BNZ | 功能描述:IC DAC 16BIT SERIAL INP 20DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。