- 您現在的位置：買賣IC網 > PDF目錄373921 > AD7869AQ (ANALOG DEVICES INC) LC2MOS Complete, 14-Bit Analog I/O System PDF資料下載
參數資料
| 型號： | AD7869AQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | LC2MOS Complete, 14-Bit Analog I/O System |
| 中文描述： | 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP24 |
| 封裝： | 0.300 INCH, HERMETIC SEALED, CERDIP-24 |
| 文件頁數： | 12/16頁 |
| 文件大小： | 297K |
| 代理商： | AD7869AQ |
AD7869
–12–
REV. A
AD7869–T MS32020 Interface
Figure 18 shows an interface that is suitable for the T MS32020/
T MS320C25 processors. T his interface is configured for syn-
chronous, continuous clock operation. Note the AD7869 will
not correctly interface to these processors if the AD7869 is con-
figured for a noncontinuous clock. Conversion starts and DAC
updating are controlled by an external timer.
TMS32020/
TMS320C25
FSX
DX
TCLK
DT
TFS
*ADDITIONAL PINS OMITTED FOR CLARITY
LDAC
FSR
CLKR
DR
RCLK
DR
CONVST
RFS
CONTROL
TIMER
AD7869*
4.7k
2k
4.7k
5V
+
5V
–
CLKX
Figure 18. AD7869–TMS32020/TMS32025 Interface
APPLICAT ION HINT S
Good printed circuit board (PCB) layout is as important as the
circuit design itself in achieving high speed A/D performance.
T he AD7869’s comparator is required to make bit decisions on
an LSB size of 366
μ
V. T o achieve this, the designer has to be
conscious of noise both in the ADC itself and in the preceding
analog circuitry. Switching mode power supplies are not recom-
mended as the switching spikes will feed through to the com-
parator causing noisy code transitions. Other causes of concern
are ground loops and digital feedthrough from microprocessors.
T hese are factors that influence any ADC, and a proper PCB
layout that minimizes these effects is essential for best
performance.
LAY OUT HINT S
Ensure that the layout for the printed circuit board has the digi-
tal and analog signal lines separated as much as possible. T ake
care not to run any digital track alongside an analog signal track.
Guard (screen) the analog input with AGND.
Establish a single point analog ground (star ground), separate
from the logic system ground, as close as possible to the
AD7869 AGND pins. Connect all other grounds and the
AD7869 DGND to this single analog ground point. Do not
connect any other digital grounds to this analog ground point.
Low impedance analog and digital power supply common re-
turns are essential to low noise operation of the ADC, so make
the foil width for these tracks as wide as possible. T he use of
ground planes minimizes impedance paths and also guards the
analog circuitry from digital noise. T he circuit layout of Figures
22 and 23 have both analog and digital ground planes that are
kept separated and only joined together at the AD7869 AGND
pins.
NOISE
K eep the input signal leads to V
IN
and signal return leads from
AGND as short as possible to minimize input noise coupling. In
applications where this is not possible, use a shielded cable be-
tween the source and the ADC. Reduce the ground circuit im-
pedance as much as possible since any potential difference in
grounds between the signal source and the ADC appears as an
error voltage in series with the input signal.
INPUT /OUT PUT BOARD
Figure 19 shows an analog I/O board based on the AD7869.
T he corresponding printed circuit (PC) board layout and
silkscreen are shown in Figures 21 to 23.
T he analog input to the AD7869 is buffered with an AD711 op
amp. T here is a component grid provided near the analog input
on the PC board that may be used for an antialiasing filter for
the ADC or a reconstruction filter for the DAC or any other
conditioning circuitry. T o facilitate this option, there are two
wire links (labeled LK 1 and LK 2) required on the analog input
and output tracks.
T he board contains a SHA circuit that can be used on the out-
put of the AD7869 DAC to extend the very good performance
of the part over a wider frequency range. T he increased perfor-
mance from the SHA can be seen from Figures 14 and 15 of
this data sheet. A wire link (labeled LK 3) connects the board
output to either the SHA output or directly to the AD7869
DAC output .
T here are three
LDAC
link options on the board;
LDAC
can be
driven from an external source independent of
CONVST
,
LDAC
can be tied to
CONVST
or
LDAC
can be tied to GND.
Choosing the latter option disables the SHA operation and
places the SHA permanently in the track mode.
Microprocessor connections to the board are made by a 9-way
D-type connector. T he pinout is shown in Figure 20. T he
ADC’s digital outputs are buffered with 74HC4050s. T hese
buffers provide a higher current output capability for high
capacitance loads or cables. Normally, these buffers are not re-
quired as the AD7869 will be sitting on the same board as the
processor.
POWE R SUPPLY CONNE CT IONS
T he PC board requires two analog power supplies and one 5 V
digital supply. Connections to the analog supply are made di-
rectly to the PC board as shown on the silkscreen in Figure 21.
T he connections are labeled V+ and V–, and the range for both
of these supplies is 12 V to 15 V. Connections to the 5 V digital
supply are made through the D-type connector SK T 6. T he
±
5 V analog supply required by the AD7869 is generated from
two voltage regulators on the V+ and V– supplies.
WIRE LINK OPT IONS
LK 1, Analog Input Link
LK 1 connects the analog input to a component grid or to a
buffer amplifier which drives the ADC input.
LK 2, Analog Output Link
LK 2 connects the analog output to the component grid or to ei-
ther the SHA or DAC output (see LK 3).
LK 3, SHA or DAC Select
T he analog output may be taken directly from the DAC or from
a SHA at the output of the DAC.
LK 4, DAC Reference Selection
T he DAC reference may be connected to either the ADC refer-
ence output (RO ADC) or to the DAC reference (RO DAC).
相關PDF資料 |
PDF描述 |
|---|---|
| AD7869JN | LC2MOS Complete, 14-Bit Analog I/O System |
| AD7869JR | LC2MOS Complete, 14-Bit Analog I/O System |
| AD7870A | Complete, 12-Bit, 100 kHz , Sampling ADC(完備的,頻率為100kHz,12位A/D轉換器) |
| AD7870CQ | LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
| AD7870JN | 12-Bit, 53 MSPS ADC SE/Diff imputs w/range of 2 to 3Vpp, Int/Ext Ref., Out of Range Indicator 28-SSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7869JN | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete, 14-Bit Analog I/O System |
| AD7869JNZ | 功能描述:IC I/O PORT 14BIT ANLG 24DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD7869JQ | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD7869JR | 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Single DAC 14-Bit 28-Pin SOIC W 制造商:Analog Devices 功能描述:DATA ACQ SYS SGL ADC SGL DAC 14BIT 28SOIC W - Rail/Tube |
| AD7869JRZ | 功能描述:IC I/O PORT 14BIT ANLG 28SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
發布緊急采購，3分鐘左右您將得到回復。