欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7887BR
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: +2.7 V to +5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead uSOIC
中文描述: 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8
封裝: 0.150 INCH, MS-012AA, SOIC-8
文件頁數: 10/16頁
文件大小: 133K
代理商: AD7887BR
REV. B
AD7887
–10–
as the source impedance increases and performance will degrade.
Figure 10 shows a graph of the total harmonic distortion versus
analog input signal frequency for different source impedances.
INPUT FREQUENCY – kHz
–90
0.15
42.14
T
10.89
31.59
21.14
–85
–80
–75
–70
–65
49.86
THD vs. FREQUENCY FOR DIFFERENT
SOURCE IMPEDANCES
V
= 5V
5V EXT REFERENCE
R
IN
= 1k
V
, C
IN
= 100pF
R
IN
= 50
V
, C
IN
= 2.2nF
R
IN
= 10
V
, C
IN
= 10nF
Figure 10. THD vs. Analog Input Frequency
On-Chip Reference
T he AD7887 has an on-chip 2.5 V reference. T his reference can
be enabled or disabled by clearing or setting the REF bit in the
control register respectively. If the on-chip reference is to be
used externally in a system then it must be buffered before it is
applied elsewhere. If an external reference is applied to the
device, then the internal reference is automatically overdriven.
However, it is advised to disable the internal reference by setting
the REF bit in the control register when an external reference is
applied in order to obtain optimum performance from the de-
vice. When the internal reference is disabled, SW1 in Figure 11
will open and the input impedance seen at the AIN1/V
REF
pin is
the input impedance of the reference buffer, which is in the
region of gigaohms. When the internal reference is enabled the
input impedance seen at the pin is typically 10 k
. When the
AD7887 is operated in two-channel mode, the reference is taken
from V
DD
internally and not from the on-chip 2.5 V reference.
2.5V
10k
V
SW1
AIN1/V
REF
Figure 11. On-Chip Reference Circuitry
POWE R-DOWN OPT IONS
T he AD7887 provides flexible power management to allow the
user to achieve the best power performance for a given through-
put rate.
T he power management options are selected by programming
the power management bits (i.e., PM1 and PM0) in the control
register. T able II summarizes the available options. When the
power management bits are programmed for either of the auto
power-down modes, the part will enter power-down mode on
the 16th rising SCLK edge after the falling edge of
CS
. T he
first falling SCLK edge after the
CS
falling edge will cause the
part to power up again. When the AD7887 is in Mode 1, i.e.,
PM1 = PM0 = 0, the part will enter shutdown on the rising
edge of
CS
and power up from shutdown on the falling edge of
CS
. If
CS
is brought high during the conversion in this mode,
the part will immediately enter shutdown.
Power-Up T imes
T he AD7887 has an approximate 1
μ
s power-up time when
powering up from standby or when using an external reference.
When V
DD
is first connected the AD7887 will power up in
Mode 1, i.e., PM1 = PM0 = 0. T he part is put into shutdown
on the rising edge of
CS
in this mode. A subsequent power-up
from shutdown will take approximately 5
μ
s. T he AD7887
wake-up time is very short in the autostandby mode so it is
possible to wake-up the part and carry out a valid conversion in
the same read/write operation.
POWE R VS. T HROUGHPUT RAT E
By operating the AD7887 in autoshutdown, autostandby mode
or Mode 1, the average power consumption of the AD7887
decreases at lower throughput rates. Figure 12 shows how, as
the throughput rate is reduced, the device remains in its power-
down state longer and the average power consumption over time
drops accordingly.
For example if the AD7887 is operated in a continuous sam-
pling mode with a throughput rate of 10 kSPS and a SCLK of
2 MHz (V
DD
= 5 V), and if PM1 = 1 and PM0 = 0, i.e., the
device is in autoshutdown mode, and the on-chip reference is
used, the power consumption is calculated as follows. T he power
dissipation during normal operation is 3.5 mW (V
DD
= 5 V). If
the power-up time is 5
μ
s, and the remaining conversion plus
acquisition time is 15.5 t
SCLK
, i.e., approximately 7.75
μ
s, (see
Figure 15a), the AD7887 can be said to dissipate 3.5 mW for
12.75
μ
s during each conversion cycle. If the throughput rate is
10 kSPS, the cycle time is 100
μ
s and the average power dissi-
pated during each cycle is (12.75/100)
×
(3.5 mW) = 446.25
μ
W.
If V
DD
= 3 V, SCLK = 2 MHz and the device is again in auto-
shutdown mode using the on-chip reference, then the power
dissipation during normal operation is 2.1 mW. T he AD7887
can now be said to dissipate 2.1 mW for 12.75
μ
s during each
conversion cycle. With a throughput rate of 10 kSPS, the aver-
age power dissipated during each cycle is (12.75/100)
×
(2.1 mW)
= 267.75
μ
W. Figure 12 shows the Power vs. T hroughput Rate
for automatic shutdown with both 5 V and 3 V supplies.
THROUGHPUT – kSPS
10
0
P
1
10
0.1
0.01
V
= 5V
SCLK = 2MHz
V
= 3V
SCLK = 2MHz
20
30
40
50
Figure 12. Power vs. Throughput
相關PDF資料
PDF描述
AD7888(中文) 2.7 V to 5.25 V, Micro Power, 8-Channel,125kSPS,12-Bit ADC(微功耗,125kSPS,8通道12位A/D轉換器)
AD7888 +2.7 V to +5.25 V, Micropower, 8-Channel, 125 kSPS, 12-Bit ADC in 16-Lead TSSOP
AD7888AR +2.7 V to +5.25 V, Micropower, 8-Channel, 125 kSPS, 12-Bit ADC in 16-Lead TSSOP
AD7888ARU +2.7 V to +5.25 V, Micropower, 8-Channel, 125 kSPS, 12-Bit ADC in 16-Lead TSSOP
AD7888BR +2.7 V to +5.25 V, Micropower, 8-Channel, 125 kSPS, 12-Bit ADC in 16-Lead TSSOP
相關代理商/技術參數
參數描述
AD7887BR-REEL 功能描述:IC ADC 12BIT 2CH SRL 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7887BR-REEL7 功能描述:IC ADC 12BIT 2CH SRL 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7887BRZ 功能描述:IC ADC 12BIT 2CHAN SRL 8SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7887BRZ-REEL 功能描述:IC ADC 12BIT 2CHAN SRL 8SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7887BRZ-REEL7 功能描述:IC ADC 12BIT 2CHAN SRL 8SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
主站蜘蛛池模板: 拉萨市| 精河县| 全州县| 济宁市| 丽水市| 济南市| 武宣县| 辰溪县| 兖州市| 略阳县| 自贡市| 巢湖市| 容城县| 东平县| 酒泉市| 青阳县| 祁东县| 屯留县| 上思县| 香港| 布尔津县| 东源县| 铜川市| 鞍山市| 金乡县| 安吉县| 湘潭县| 临沂市| 望江县| 寻乌县| 交口县| 宿松县| 唐山市| 新营市| 合水县| 敦化市| 三江| 兴仁县| 舒城县| 彰武县| 连平县|