欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7890BR-2
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: LC2MOS 8-Channel, 12-Bit Serial, Data Acquisition System
中文描述: 8-CH 12-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PDSO24
封裝: MS-013AD, SOIC-24
文件頁數: 10/20頁
文件大?。?/td> 302K
代理商: AD7890BR-2
AD7890
–10–
REV. A
If the application requires a reference with a tighter tolerance or
the AD7890 needs to be used with a system reference, then the
user has the option of connecting an external reference to this
REF OUT /REF IN pin. T he external reference will effectively
overdrive the internal reference and thus provide the reference
source for the ADC. T he reference input is buffered but has a
nominal 2 k
resistor connected to the AD7890’s internal refer-
ence. Suitable reference sources for the AD7890 include the
AD680, AD780 and REF-43 precision +2.5 V references.
T iming and Control Section
T he AD7890 is capable of two interface modes, selected by the
SMODE input. T he first of these is a self-clocking mode where the
part provides the frame sync, serial clock and serial data at the end
of conversion. In this mode the serial clock rate is determined by
the master clock rate of the part (at CLK IN input). T he second
mode is an external clocking mode where the user provides the
frame sync and serial clock signals to obtain the serial data from the
part. In this second mode, the user has control of the serial clock
rate up to a maximum of 10 MHz. T he two modes are discussed in
more detail in the Serial Interface section.
T he part also provides hardware and software conversion start
features. T he former provides a well-defined sampling instant
with the track/hold going into hold on the rising edge of the
CONVST
signal. For the software conversion start, a write to
the CONV bit to the Control Register initiates the conversion
sequence. However, for the software conversion start an internal
pulse has to time out before the input signal is sampled. T his
pulse, plus the difficult in maintaining exactly equal delays
between each software conversion start command, means that
the dynamic performance of the AD7890 may have difficulty
meeting spec when used in software conversion start mode.
T he AD7890 provides separate channel select and conversion start
control. T his allows the user to optimize the throughput rate of the
system. Once the track/hold has gone into hold mode, the input
channel can be updated and the input voltage can settle to the new
value while the present conversion is in progress.
Assuming the internal pulse has timed out before the
CONVST
pulse is exercised, the conversion will consist of 14.5 master
clock cycles. In the self-clocking mode, the conversion time is
defined as the time from the rising edge of
CONVST
to the fall-
ing edge of
RFS
(i.e., when the device starts to transmit its con-
version result). T his time includes the 14.5 master clock cycles
plus the updating of the output register and delay time in out-
putting the
RFS
signal, resulting in a total conversion time of
5.9
μ
s maximum. Figure 4 shows the conversion timing for the
AD890 when used in the Self-Clocking (Master) Mode with
hardware
CONVST
. T he timing diagram assumes that the
internal pulse is not active when the
CONVST
signal goes high.
T o ensure this, the channel address to be converted should be
selected by writing to the Control Register prior to the
CONVST
pulse. Sufficient setup time should be allowed
between the Control Register write and the
CONVST
to ensure
that the internal pulse has timed out. T he duration of the inter-
nal pulse (and hence the duration of setup time) depends on the
value of C
EX T
.
T rack/Hold Section
T he SHA IN input on the AD7890 connects directly to the
input stage of the track/hold amplifier. T his is a high impedance
input with input leakage currents of less than 50 nA. Connect-
ing the MUX OUT pin directly to the SHA IN pin connects the
multiplexer output directly to the track/hold amplifier. T he
input voltage range for this input is 0 V to +2.5 V. If external
circuitry is connected between MUX OUT and SHA IN, then
the user must ensure that the input voltage range to the SHA
IN input is 0 V to +2.5 V to ensure that the full dynamic range
of the converter is utilized.
T he track/hold amplifier on the AD7890 allows the ADC to
accurately convert an input sine wave of full-scale amplitude to
12-bit accuracy. T he input bandwidth of the track/hold is
greater than the Nyquist rate of the ADC even when the ADC is
operated at its maximum throughput rate of 117 kHz (i.e., the
track/hold can handle input frequencies in excess of 58 kHz).
T he track/hold amplifier acquires an input signal to 12-bit accu-
racy in less than 2
μ
s. T he operation of the track/hold is essen-
tially transparent to the user. T he track/hold amplifier goes from
its tracking mode to its hold mode at the start of conversion.
T he start of conversion is the rising edge of
CONVST
(assum-
ing the internal pulse has timed out) for hardware conversion
starts and for software conversion starts is the point where the
internal pulse is timed out. T he aperture time for the track/hold
(i.e., the delay time between the external
CONVST
signal and
the track/hold actually going into hold) is typically 15 ns. For
software conversion starts, the time depends on the internal
pulse widths. T herefore, for software conversion starts, the sam-
pling instant is not very well defined. For sampling systems
which require well defined, equidistant sampling, it may not be
possible to achieve optimum performance from the part using
the software conversion start. At the end of conversion, the part
returns to its tracking mode. T he acquisition time of the track/
hold amplifier begins at this point.
Reference Section
T he AD7890 contains a single reference pin, labelled
REF OUT /REF IN, which either provides access to the part’s
own +2.5 V reference or to which an external +2.5 V reference
can be connected to provide the reference source for the part.
T he part is specified with a +2.5 V reference voltage. Errors in
the reference source will result in gain errors in the AD7890’s
transfer function and will add to the specified full-scale errors
on the part. On the AD7893-10, it will also result in an offset
error injected in the attenuator stage.
T he AD7890 contains an on-chip +2.5 V reference. T o use this
reference as the reference source for the AD7890, simply con-
nect a 0.1
μ
F disc ceramic capacitor from the REF OUT / REF
IN pin to AGND. T he voltage which appears at this pin is inter-
nally buffered before being applied to the ADC. If this reference
is required for use external to the AD7890, it should be buffered
as the source impedance of this output is 2 k
nominal. T he
tolerance on the internal reference is
±
10 mV at 25
°
C with a
typical temperature coefficient of 25 ppm/
°
C and a maximum
error over temperature of
±
25 mV.
相關PDF資料
PDF描述
AD7890BR-4 LC2MOS 8-Channel, 12-Bit Serial, Data Acquisition System
AD7890AR-10 Side Entry Connector Hood; Enclosure Material:Aluminum Alloy; For Use With:C146 Rectangular Circular Connectors; Connecting Termination:Screw; Gender:Male; No. of Contacts:48; Operating Voltage:400V; Series:C-146 RoHS Compliant: Yes
AD7890AR-2 Circular Connector Cable Assembly; Connector Type A:Circular Receptacle; Connector Type B:Stripped End Leads; Cable Length:10ft; Features:500 Mating Cycles, PVC Jacket, IP67 Rating, E63093 Rated Connector; No. of Contacts:6 RoHS Compliant: Yes
AD7890SQ-10 20 Characters x 4 Lines, 5x7 Dot Matrix Character and Cursor
AD7890SQ-2 20 Characters x 4 Lines, 5x7 Dot Matrix Character and Cursor
相關代理商/技術參數
參數描述
AD7890BR-2REEL 制造商:Analog Devices 功能描述:ADC Single SAR 117ksps 12-bit Serial 24-Pin SOIC W T/R
AD7890BR-4 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7890BR-4REEL 制造商:Analog Devices 功能描述:ADC Single SAR 117ksps 12-bit Serial 24-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 117KSPS 12-BIT SERL 24SOIC W - Tape and Reel
AD7890BRZ-10 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7890BRZ-10REEL 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
主站蜘蛛池模板: 库尔勒市| 调兵山市| 冕宁县| 神农架林区| 合作市| 西乌| 闽侯县| 赤壁市| 温州市| 定襄县| 宝坻区| 宁南县| 韶山市| 克山县| 普陀区| 南溪县| 开平市| 呼玛县| 广安市| 临城县| 云梦县| 梨树县| 格尔木市| 佛山市| 甘德县| 扬州市| 平湖市| 巩义市| 易门县| 左权县| 庆安县| 吉林市| 宁晋县| 云南省| 天镇县| 德令哈市| 平塘县| 铅山县| 巴青县| 安丘市| 金山区|