欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7890BR-2
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: LC2MOS 8-Channel, 12-Bit Serial, Data Acquisition System
中文描述: 8-CH 12-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PDSO24
封裝: MS-013AD, SOIC-24
文件頁數: 7/20頁
文件大小: 302K
代理商: AD7890BR-2
AD7890
–7–
REV. A
T E RMINOLOGY
Signal to (Noise + Distortion) Ratio
T his is the measured ratio of signal to (noise + distortion) at the
output of the A/D converter. T he signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (f
S
/2), excluding dc.
T he ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the quan-
tization noise. T he theoretical signal to (noise + distortion) ratio
for an ideal N-bit converter with a sine wave input is given by:
Signal to (Noise + Distortion) = (6.02N + 1.76) dB
T hus for a 12-bit converter, this is 74 dB.
T otal Harmonic Distortion
T otal harmonic distortion (T HD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7890, it is defined as:
THD
(
dB
)
=
20 log
V
2
2
+
V
3
2
+
V
4
V
1
2
+
V
5
2
+
V
6
2
where
V
1
is the rms amplitude of the fundamental and
V
2
,
V
3
,
V
4
,
V
5
and
V
6
are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to f
S
/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for parts
where the harmonics are buried in the noise floor, it will be a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa
±
nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for which
neither m nor n are equal to zero. For example, the second order
terms include (fa + fb) and (fa – fb), while the third order terms
include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa – 2fb).
T he AD7890 is tested using the CCIF standard where two
input frequencies near the top end of the input bandwidth are
used. In this case, the second and third order terms are of differ-
ent significance. T he second order terms are usually distanced
in frequency from the original sine waves while the third order
terms are usually at a frequency close to the input frequencies.
As a result, the second and third order terms are specified sepa-
rately. T he calculation of the intermodulation distortion is as
per the T HD specification where it is the ratio of the rms sum of
the individual distortion products to the rms amplitude of the
fundamental expressed in dBs.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a full-
scale 1 kHz signal to any one of the other seven inputs and
determining how much that signal is attenuated in the chan-
nel of interest. T he figure given is the worst case across all
eight channels.
Relative Accuracy
Relative accuracy or endpoint nonlinearity is the maximum
deviation from a straight line passing through the endpoints of
the ADC transfer function.
Differential Nonlinearity
T his is the difference between the measured and the ideal 1LSB
change between any two adjacent codes in the ADC.
Positive Full-Scale E rror (AD7890-10)
T his is the deviation of the last code transition (01 . . . 110 to
01 . . . 111) from the ideal (4
×
REF IN – 1 LSB) after the Bipolar
Zero Error has been adjusted out.
Positive Full-Scale E rror (AD7890-4)
T his is the deviation of the last code transition (11 . . . 110 to
11 . . . 111) from the ideal (1.638
×
REF IN – 1 LSB) after the
Unipolar Offset Error has been adjusted out.
Positive Full-Scale E rror (AD7890-2)
T his is the deviation of the last code transition (11 . . . 110 to
11 . . . 111) from the ideal (REF IN – 1 LSB) after the Unipolar
Offset Error has been adjusted out.
Bipolar Zero E rror (AD7890-10)
T his is the deviation of the midscale transition (all 0s to all 1s)
from the ideal 0 V (AGND).
Unipolar Offset E rror (AD7890-2, AD7890-4)
T his is the deviation of the first code transition (00 . . . 000 to
00 . . . 001) from the ideal 0 V (AGND).
Negative Full-Scale E rror (AD7890-10)
T his is the deviation of the first code transition (10 . . . 000 to
10 . . . 001) from the ideal (–4
×
REF IN + 1 LSB) after Bipolar
Zero Error has been adjusted out.
T rack/Hold Acquisition T ime
T rack/Hold acquisition time is the time required for the output
of the track/hold amplifier to reach its final value, within
±
1/2 LSB,
after the end of conversion (the point at which the track/hold
returns to track mode). It also applies to situations where a
change in the selected input channel takes place or where there
is a step input change on the input voltage applied to the selected
V
IN
input of the AD7890. It means that the user must wait for
the duration of the track/hold acquisition time after the end of
conversion or after a channel change/step input change to V
IN
before starting another conversion, to ensure that the part oper-
ates to specification.
相關PDF資料
PDF描述
AD7890BR-4 LC2MOS 8-Channel, 12-Bit Serial, Data Acquisition System
AD7890AR-10 Side Entry Connector Hood; Enclosure Material:Aluminum Alloy; For Use With:C146 Rectangular Circular Connectors; Connecting Termination:Screw; Gender:Male; No. of Contacts:48; Operating Voltage:400V; Series:C-146 RoHS Compliant: Yes
AD7890AR-2 Circular Connector Cable Assembly; Connector Type A:Circular Receptacle; Connector Type B:Stripped End Leads; Cable Length:10ft; Features:500 Mating Cycles, PVC Jacket, IP67 Rating, E63093 Rated Connector; No. of Contacts:6 RoHS Compliant: Yes
AD7890SQ-10 20 Characters x 4 Lines, 5x7 Dot Matrix Character and Cursor
AD7890SQ-2 20 Characters x 4 Lines, 5x7 Dot Matrix Character and Cursor
相關代理商/技術參數
參數描述
AD7890BR-2REEL 制造商:Analog Devices 功能描述:ADC Single SAR 117ksps 12-bit Serial 24-Pin SOIC W T/R
AD7890BR-4 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7890BR-4REEL 制造商:Analog Devices 功能描述:ADC Single SAR 117ksps 12-bit Serial 24-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 117KSPS 12-BIT SERL 24SOIC W - Tape and Reel
AD7890BRZ-10 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7890BRZ-10REEL 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
主站蜘蛛池模板: 花莲市| 浦县| 阿荣旗| 临夏市| 凭祥市| 白玉县| 双桥区| 太和县| 新绛县| 金昌市| 平和县| 保德县| 隆安县| 宝应县| 米林县| 鄄城县| 平安县| 通辽市| 汕头市| 民乐县| 甘德县| 黑河市| 荣成市| 灌阳县| 辉县市| 深圳市| 枣庄市| 广州市| 临沭县| 伊金霍洛旗| 凉山| 赤峰市| 丰台区| 江华| 屯门区| 城固县| 浠水县| 桐柏县| 新源县| 自治县| 太原市|