欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7890SQ-2
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: 20 Characters x 4 Lines, 5x7 Dot Matrix Character and Cursor
中文描述: 8-CH 12-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, CDIP24
封裝: 0.300 INCH, CERDIP-24
文件頁數: 5/20頁
文件大小: 302K
代理商: AD7890SQ-2
AD7890
–5–
REV. A
PIN FUNCT ION DE SCRIPT ION
Pin
Mnemonic
Description
1
2
AGND
SMODE
Analog Ground. Ground reference for track/hold, comparator and DAC.
Control Input. Determines whether the part operates in its External Clocking (slave) or Self-Clocking
(master) serial mode. With SMODE at a logic low, the part is in its Self-Clocking serial mode with
RFS
and SCLK as outputs. T his Self-Clocking mode is useful for connection to shift registers or to
serial ports of DSP processors. With SMODE at a logic high, the part is in its External Clocking
serial mode with SCLK and
RFS
as inputs. T his External Clocking mode is useful for connection to
the serial port of microcontrollers such as the 8X C51 and the 68HCX X and for connection to the
serial ports of DSP processors.
Digital Ground. Ground reference for digital circuitry.
External Capacitor. An external capacitor is connected to this pin to determine the length of the
internal pulse (see
CONVST
input and Control Register section). Larger capacitances on this pin
extend the pulse to allow for settling time delays through an external antialiasing filter or signal
conditioning circuitry.
Convert Start. Edge-triggered logic input. A low to high transition on this input puts the track/hold
into hold and initiates conversion provided that the internal pulse has timed out (see Control
Register section). If the internal pulse is active when the
CONVST
goes high, the track/hold will not
go into hold until the pulse times out. If the internal pulse has timed out when
CONVST g
oes high,
the rising edge of
CONVST
drives the track/hold into hold and initiates conversion.
Clock Input. An external T T L-compatible clock is applied to this input pin to provide the clock
source for the conversion sequence. In the Self-Clocking serial mode, the SCLK output is derived
from this CLK IN pin.
Serial Clock Input. In the External Clocking (slave) mode (see Serial Interface section) this is an
externally applied serial clock which is used to load serial data to the control register and to access
data from the output register. In the Self-Clocking (master) mode, the internal serial clock, which is
derived from the clock input (CLK IN), appears on this pin. Once again, it is used to load serial data
to the control register and to access data from the output register.
T ransmit Frame Synchronization Pulse. Active low logic input with serial data expected after the
falling edge of this signal.
Receive Frame Synchronization Pulse. In the External Clocking mode, this pin is an active low logic
input with
RFS
provided externally as a strobe or framing pulse to access serial data from the output
register. In the Self-Clocking mode, it is an active low output which is internally generated and
provides a strobe or framing pulse for serial data from the output register. For applications which
require that data be transmitted and received at the same time,
RFS
and
TFS
should be connected
together.
Serial Data Output. Sixteen bits of serial data are provided with one leading zero, preceding the three
address bits of the Control register and the 12 bits of conversion data. Serial data is valid on the
falling edge of SCLK for sixteen edges after
RFS
goes low. Output coding from the ADC is 2s
complement for the AD7890-10 and straight binary for the AD7890-4 and AD7890-2.
Serial Data Input. Serial data to be loaded to the control register is provided at this input. T he first
five bits of serial data are loaded to the control register on the first five falling edges of SCLK after
TFS
goes low. Serial data on subsequent SCLK edges is ignored while
TFS
remains low.
Positive supply voltage, +5 V
±
5%.
Multiplexer Output. T he output of the multiplexer appears at this pin. T he output voltage range
from this output is 0 V to +2.5 V for the nominal analog input range to the selected channel. T he
output impedance of this output is nominally 3.5 k
. If no external antialiasing filter is required,
MUX OUT should be connected to SHA IN.
T rack/Hold Input. T he input to the on-chip track/hold is applied to this pin. It is a high impedance
input and the input voltage range is 0 V to +2.5 V.
Analog Ground. Ground reference for track/hold, comparator and DAC.
Analog Input Channel 1. Single-ended analog input. T he analog input range on is
±
10 V
(AD7890-10), 0 V to +4.096 V (AD7890-4) and 0 V to +2.5 V (AD7890-2). T he channel to be con-
verted is selected using the A0, A1 and A2 bits in the control register. T he multiplexer has guaran-
teed break-before-make operation.
3
4
DGND
C
EX T
5
CONVST
6
CLK IN
7
SCLK
8
TFS
9
RFS
10
DAT A OUT
11
DAT A IN
12
13
V
DD
MUX OUT
14
SHA IN
15
16
AGND
V
IN1
相關PDF資料
PDF描述
AD7890SQ-4 20 Characters x 4 Lines, 5x7 Dot Matrix Character and Cursor
AD7890AN-2 Explosion-Proof Limit Switches Series CX: Standard Housing: Side Rotary, Lever not included
AD7890AN-4 Explosion-Proof Limit Switches Series CX: Standard Housing: Side Rotary, Lever not included
AD7891YS-1 LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
AD7891YS-2 LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
相關代理商/技術參數
參數描述
AD7890SQ-4 功能描述:模數轉換器 - ADC LC2MOS 8CH 12B Data Acquisition System RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
AD7891AP1 制造商:Analog Devices 功能描述:
AD7891AP-1 功能描述:IC DAS 12BIT 8CH 44-PLCC RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7891AP-1REEL 功能描述:IC DAS 12BIT 8CH 44-PLCC RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7891AP2 制造商:Analog Devices 功能描述:
主站蜘蛛池模板: 长宁区| 萨迦县| 富民县| 高邑县| 泌阳县| 永川市| 长沙县| 海门市| 晋中市| 时尚| 共和县| 荥经县| 龙岩市| 龙泉市| 榆中县| 盐源县| 砀山县| 寿阳县| 平江县| 阜新| 仙游县| 永德县| 鄂伦春自治旗| 宁波市| 阳江市| 仲巴县| 崇礼县| 宁海县| 临江市| 太白县| 疏勒县| 新晃| 岫岩| 永德县| 武隆县| 鄢陵县| 泽州县| 手机| 黔江区| 尚志市| 合川市|