- 您現在的位置：買賣IC網 > PDF目錄373926 > AD7923 (Analog Devices, Inc.) SHROUDED HEADER 60 PIN STRAIGHT PDF資料下載
參數資料
| 型號： | AD7923 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | ADC |
| 英文描述： | SHROUDED HEADER 60 PIN STRAIGHT |
| 中文描述： | 4通道，200 kSPS的，12位序列ADC的16引腳TSSOP |
| 文件頁數： | 7/20頁 |
| 文件大小： | 430K |
| 代理商： | AD7923 |
AD7923
–7–
REV. 0
TERMINOLOGY
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The end-
points of the transfer function are zero-scale, a point 1 LSB
below the first code transition, and full-scale, a point 1 LSB
above the last code transition.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (00 . . . 000) to
(00 . . . 001) from the ideal, i.e., AGND + 1 LSB.
Offset Error Match
This is the difference in offset error between any two channels.
Gain Error
This is the deviation of the last code transition (111 . . . 110) to
(111 . . . 111) from the ideal (i.e., REF
IN
– 1 LSB) after the
offset error has been adjusted out.
Gain Error Match
This is the difference in Gain Error between any two channels.
Zero Code Error
This applies when using the twos complement output coding
option, in particular to the 2
￥
REF
IN
input range with –REF
IN
to +REF
IN
biased about the REF
IN
point. It is the deviation of
the midscale transition (all 0s to all 1s) from the ideal V
IN
voltage,
i.e., REF
IN
– 1 LSB.
Zero Code Error Match
This is the difference in Zero Code Error between any two
channels.
Positive Gain Error
This applies when using the twos complement output coding
option, in particular to the 2
￥
REF
IN
input range with –REF
IN
to +REF
IN
biased about the REF
IN
point. It is the deviation of
the last code transition (011. . .110) to (011 . . . 111) from the
ideal (i.e., +REF
IN
– 1 LSB) after the Zero Code Error has been
adjusted out.
Positive Gain Error Match
This is the difference in Positive Gain Error between any two
channels.
Negative Gain Error
This applies when using the twos complement output coding
option, in particular to the 2
￥
REF
IN
input range with –REF
IN
to +REF
IN
biased about the REF
IN
point. It is the deviation of
the first code transition (100 . . . 000) to (100 . . . 001) from the
ideal (i.e., –REF
IN
+ 1 LSB) after the Zero Code Error has been
adjusted out.
Negative Gain Error Match
This is the difference in Negative Gain Error between any two
channels.
Channel-to-Channel Isolation
Channel-to-Channel Isolation is a measure of the level of crosstalk
between channels. It is measured by applying a full-scale 400 kHz
sine wave signal to all three nonselected input channels and
determining how much that signal is attenuated in the selected
channel with a 50 kHz signal. The figure is given worst-case
across all four channels for the AD7923.
PSR (Power Supply Rejection)
Variations in power supply will affect the full-scale transition,
but not the converter’s linearity. Power supply rejection is the
maximum change in full-scale transition point due to a change
in power supply voltage from the nominal value. See Typical
Performance Characteristics.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns into track mode at the end
of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within
±
1 LSB, after the end of conversion.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the sum of all nonfundamental sig-
nals up to half the sampling frequency (f
S
/2), excluding dc. The
ratio is dependent on the number of quantization levels in the
digitization process; the more levels, the smaller the quantiza-
tion noise. The theoretical signal-to-(noise + distortion) ratio
for an ideal N-bit converter with a sine wave input is given by:
Distortion
- -
(
+
Thus for a 12-bit converter, this is 74 dB.
Total Harmonic Distortion (THD)
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7923, it is defined as:
Signal to Noise
N
dB
)
(6 02
.
)
=
+
1 76
THD dB
V
V
V
V
V
V
(
)
log
=
+
+
+
+
20
2
2
3
2
4
2
5
2
6
2
1
where
V
1
is the rms amplitude of the fundamental and
V
2
,
V
3
,
V
4
,
V
5
, and
V
6
are the rms amplitudes of the second through the
sixth harmonics.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7923BRU | Four Wall Header; No. of Contacts:60; Pitch Spacing:0.1"; No. of Rows:2; Gender:Header; Body Material:Glass-filled Polyester; Contact Plating:Nickel; Leaded Process Compatible:No; Mounting Type:Through Hole RoHS Compliant: No |
| AD7940BRJ-R2 | 3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
| AD7947 | 3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
| AD7940BRJ-REEL7 | 3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
| AD7680 | 3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7923_11 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 200 kSPS 12-Bit ADC with Sequencer in 16-Lead TSSOP |
| AD7923BRU | 功能描述:模數轉換器 - ADC 4CH 200 kSPS 12-Bit W/ Sequencer RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD7923BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 200KSPS 12-BIT SERL 16TSSOP - Tape and Reel |
| AD7923BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 16-Pin TSSOP T/R |
| AD7923BRUZ | 功能描述:IC ADC 12BIT 4CH W/SEQ 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。