- 您現在的位置：買賣IC網 > PDF目錄373927 > AD7948 (Analog Devices, Inc.) +3.3 V/+5 V Multiplying 12-Bit DACs PDF資料下載
參數資料
| 型號： | AD7948 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | +3.3 V/+5 V Multiplying 12-Bit DACs |
| 中文描述： | 3.3伏/ 5伏乘以12位DAC |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 329K |
| 代理商： | AD7948 |
AD7943/AD7945/AD7948
REV. B
–13–
GENERAL DESCRIPTION
D/A Section
The AD7943, AD7945 and AD7948 are 12-bit current-output
D/A converters. A simplified circuit diagram is shown in Fig-
ure 13. The DAC architecture is segmented. This means that
the 2 MSBs of the 12-bit data word are decoded to drive the
three switches A, B and C. The remaining 10 bits of the data
word drive the switches S0 to S9 in a standard inverting R-2R
ladder configuration.
Each of the switches A to C steers 1/4 of the total reference
current into either I
OUT1
or I
OUT2
with the remaining 1/4 of the
total current passing through the R-2R section. Switches S9 to
S0 steer binarily weighted currents into either I
OUT1
or I
OUT2
. If
I
OUT1
and I
OUT2
are kept at the same potential, a constant cur-
rent flows in each ladder leg, regardless of digital input code.
Thus, the input resistance seen at V
REF
is always constant. It is
equal to R/2. The V
REF
input may be driven by any reference
voltage or current, ac or dc that is within the Absolute Maxi-
mum Ratings.
The device provides access to the V
REF
, R
FB
, and I
OUT1
termi-
nals of the DAC. This makes the device extremely versatile and
allows it to be configured in several different operating modes.
Examples of these are shown in the following sections. The
AD7943 also has a separate I
OUT2
pin. In the AD7945 and
AD7948 this is internally tied to AGND.
When an output amplifier is connected in the standard configu-
ration of Figure 14, the output voltage is given by:
V
OUT
= –D
×
V
REF
where D is the fractional representation of the digital word
loaded to the DAC. D can be set from 0 to 4095/4096, since it
has 12-bit resolution.
V
REF
2R
R/2
R
R
R
C
A
B
S9
S8
S0
R
FB
I
OUT1
I
OUT2
2R
2R
2R
2R
2R
2R
SHOWN FOR ALL 1
S
ON DAC
Figure 13. Simplified D/A Circuit Diagram
UNIPOLAR BINARY OPERATION
(Two-Quadrant Multiplication)
Figure 14 shows the standard unipolar binary connection dia-
gram for the AD7943, AD7945 and AD7948. When V
IN
is an
ac signal, the circuit performs two-quadrant multiplication.
Resistors R1 and R2 allow the user to adjust the DAC gain
error. With a specified gain error of 2 LSBs over temperature,
these are not necessary in many applications. Circuit offset is
due completely to the output amplifier offset. It can be re-
moved by adjusting the amplifier offset voltage. Alternatively,
choosing a low offset amplifier makes this unnecessary.
A1 should be chosen to suit the application. For example, the
OP07 is ideal for very low bandwidth applications (10 kHz or
I
OUT1
I
OUT2
A1
V
OUT
SIGNAL GROUND
A1: OP07
AD711
AD843
AD845
AGND
DAC
V
REF
R1 20
V
AD7943/45/48
V
IN
R2 10
V
RFB
C1
NOTES
1. ONLY ONE DAC IS SHOWN FOR CLAIRITY.
2. DIGITAL INPUT CONNECTIONS ARE OMITTED.
3. C1 PHASE COMPENSATION (5 – 15pF) MAY BE REQUIRED
WHEN USING HIGH SPEED AMPLIFIER.
Figure 14. Unipolar Binary Operation
lower) while the AD711 is suitable for medium bandwidth ap-
plications (200 kHz or lower). For high bandwidth applications
of greater than 200 kHz, the AD843 and AD847 offer very fast
settling times.
The code table for Figure 14 is shown in Table III.
Table III. Unipolar Binary Code
Digital Input
MSB LSB
Analog Output
(V
OUT
as Shown in Figure 14)
–V
REF
(4095/4096)
–V
REF
(2049/4096)
–V
REF
(2048/4096)
–V
REF
(2047/4096)
–V
REF
(1/4096)
–V
REF
(0/4096) = 0
1111 1111 1111
1000 0000 0001
1000 0000 0000
0111 1111 1111
0000 0000 0001
0000 0000 0000
NOTE
Nominal LSB size for the circuit of Figure 14 is given by: V
REF
(1/4096).
相關PDF資料 |
PDF描述 |
|---|---|
| AD7948BN | +3.3 V/+5 V Multiplying 12-Bit DACs |
| AD7948BR | +3.3 V/+5 V Multiplying 12-Bit DACs |
| AD7948BRS | +3.3 V/+5 V Multiplying 12-Bit DACs |
| AD7943ARS-B | +3.3 V/+5 V Multiplying 12-Bit DACs |
| AD7945ARS-B | +3.3 V/+5 V Multiplying 12-Bit DACs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7948AN-B | 制造商:Rochester Electronics LLC 功能描述:BYTE 12-B IOUT DAC IC - Bulk 制造商:Analog Devices 功能描述: |
| AD7948ANZ-B | 功能描述:IC DAC 12BIT MULT PARALL 20DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| AD7948ARS-B | 功能描述:IC DAC 12BIT MULT PARALL 20-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| AD7948ARS-BREEL | 功能描述:IC DAC 12BIT MULT PARALL 20-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD7948ARSZ-B | 功能描述:IC DAC 12BIT MULT PARALL 20SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
發布緊急采購，3分鐘左右您將得到回復。