- 您現在的位置：買賣IC網 > PDF目錄373927 > AD7993BRU-1 (ANALOG DEVICES INC) 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP PDF資料下載
參數資料
| 型號： | AD7993BRU-1 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| 中文描述： | 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | MO-153-AB, TSSOP-16 |
| 文件頁數： | 23/27頁 |
| 文件大小： | 277K |
| 代理商： | AD7993BRU-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁
AD7994/AD7993
–23–
REV. PrF
PRELIMINARY TECHNICAL DATA
Figure 14. Reading two bytes of data from the Conversion
Result Register
Figure 13. Reading a single byte of data from a selected
register
device will win communication rights via standard I
2
C
arbitration during the slave address transfer.
The ALERT output becomes active when the value in the
Conversion Result Register exceeds the value in the
DATA
HIGH
Register or falls below the value in the
DATA
LOW
Register . It is reset when a write operation to
the Configuration register sets D1 to a 1, or when the
conversion result returns N LSBs below or above the value
stored in the DATA
HIGH
Register or DATA
LOW
Register
respectively. N is the value in the Hysteresis register. (See
Limit Registers section)
The ALERT output requires an external pull-up resistor.
This can be connected to a voltage different from V
DD
provided the maximum voltage rating of the ALERT out-
put pin is not exceeded. The value of the pull-up resistor
depends on the application, but should be as large as pos-
sible to avoid excessive sink currents at the ALERT out-
put.
ALERT/BUSY PIN
The ALERT/BUSY may be configured as an Alert or
Busy ouput as shown in Table VI.
SMBus ALERT
The AD7994/AD7993 ALERT output is an SMBus inter-
rupt line for devices that want to trade their ability to
master for an extra pin. The AD7994/AD7993 is a slave
only device and uses the SMBus ALERT to signal the
host device that it wants to talk. The SMBus ALERT on
the AD7994/AD7993 is used as an out of conversion
range indicator (a limit violation indicator).
The ALERT pin has an open-drain configuration which
allows the ALERT outputs of several AD7994/AD7993
devices to be wired-AND together when the ALERT pin
is active low. D0 of the Configuration Register is used to
set the active polarity of the ALERT output. The power-
up default is active low. The ALERT function can be
disabled or enabled by setting D2 of the Configuration
Register to 1 or 0 respectively.
The host device can process the ALERT interrupt and
simultaneously access all SMBus ALERT devices through
the alert response address. Only the device which pulled
the ALERT low will acknowledge the ARA (Alert Re-
sponse Address). If more than one device pulls the
ALERT pin low, the highest priority (lowest address)
SDA
NO ACK. BY
MASTER
START BY
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
SINGLE DATA BYTE FROM AD7994/3
ACK. BY
AD7994/3
1
9
1
9
D7
D6
D5
D2
D1
D0
R/
A0
A1
A2
A3
0
1
SCL
STOP BY
MASTER
D4
D3
0
SDA
ACK. BY
MASTER
START BY
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
MOST SIGNIFICANT DATA BYTE FROM
AD7994/3
ACK. BY
AD7994/3
1
9
1
9
Alert_
Flag
D10
D9
D8
R/
A0
A1
A2
A3
0
0
SCL
1
D11
NO ACK. BY
MASTER
FRAME 3
LEAST SIGNIFICANT DATA BYTE FROM
AD7994/3
1
9
D7
D6
D5
D2
D1/0
D0/0
STOP BY
MASTER
D4
D3
SCL (CONTINUED)
SDA (CONTINUED)
CH ID1CH ID0
0
相關PDF資料 |
PDF描述 |
|---|---|
| AD7997 | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| AD7997BRU-0 | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| AD7997BRU-0REEL | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| AD7997BRU-1 | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| AD7997BRU-1REEL | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7993BRU-1REEL | 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7993BRUZ-0 | 功能描述:IC ADC 10BIT 4CH W/I2C 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7993BRUZ-0REEL | 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7993BRUZ-1 | 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7993BRUZ-1REEL | 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。