- 您現在的位置：買賣IC網 > PDF目錄373927 > AD7994BRU-1 (ANALOG DEVICES INC) 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP PDF資料下載
參數資料
| 型號： | AD7994BRU-1 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| 中文描述： | 4-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | MO-153-AB, TSSOP-16 |
| 文件頁數： | 10/27頁 |
| 文件大?。?/td> | 277K |
| 代理商： | AD7994BRU-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
AD7994/AD7993
–10–
REV. PrF
PRELIMINARY TECHNICAL DATA
Channel-to-Channel Isolation
Channel-to-Channel Isolation is a measure of the level of
crosstalk between channels. It is measured by applying a
fullscale TBD kHz sine wave signal to the nonselected
input channels and determining how much the TBD kHz
signal is attenuated in the selected channel.
This figure is
given worse case across all channels.
Aperture Delay
This is the measured interval between the leading edge of
the sampling clock and the point at which the ADC actu-
ally takes the sample.
Aperture Jitter
This is the sample-to-sample variation in the effective
point in time at which the sample is taken.
Full Power Bandwidth
The Full Power Bandwidth of an ADC is that input fre-
quency at which the amplitude of the reconstructed Fun-
damental is reduced by 0.1 dB or 3 dB for a full-scale
input
PSRR (Power Supply Rejection)
The power supply rejection ratio is defined as the ratio of
the power in the ADC output at full-scale frequency, f, to
the power of a 200 mV p-p sine wave applied to the ADC
V
DD
supply of frequency f
s
.
PSRR (dB) = 10
log (Pf/Pfs)
Pf
is the power at frequency f in the ADC output;
Pfs
is
the power at frequency fs coupled into the ADC V
DD
sup-
ply.
Integral Nonlinearity
This is the maximum deviation from a straight line pass-
ing through the endpoints of the ADC transfer function.
The endpoints of the transfer function are zero scale, a
point 1 LSB below the first code transition, and full scale,
a point 1 LSB above the last code transition.
Differential Nonlinearity
This is the difference between the measured and the ideal 1
LSB change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (00 . . .
000) to (00 . . . 001) from the ideal, i.e AGND + 1LSB
Offset Error Match
This is the difference in offset error between any two
channels.
Gain Error
This is the deviation of the last code transition (111 . . .
110) to (111 . . . 111) from the ideal (i.e., REF
IN
– 1
LSB) after the offset error has been adjusted out.
Gain Error Match
This is the difference in Gain error between any two chan-
nels.
TERMINOLOGY
Signal to (Noise + Distortion) Ratio
This is the measured ratio of signal to (noise + distortion)
at the output of the A/D converter. The signal is the rms
amplitude of the fundamental. Noise is the sum of all
nonfundamental signals up to half the sampling frequency
(f
S
/2), excluding dc. The ratio is dependent on the num-
ber of quantization levels in the digitization process; the
more levels, the smaller the quantization noise. The theo-
retical signal to (noise + distortion) ratio for an ideal N-
bit converter with a sine wave input is given by:
Signal to
(
Noise + Distortion
)
=
(6.02
N +
1.76)
dB
Thus for a 12-bit converter, this is 74 dB
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms
sum of harmonics to the fundamental. For the AD7994/
AD7993, it is defined as:
THD (dB )
=
20 log
V
2
2
+
V
3
2
+
V
4
2
+
V
5
2
+
V
6
2
V
1
where
V
1
is the rms amplitude of the fundamental and
V
2
,
V
3
,
V
4
,
V
5
and
V
6
are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio
of the rms value of the next largest component in the
ADC output spectrum (up to f
S
/2 and excluding dc) to
the rms value of the fundamental. Normally, the value
of this specification is determined by the largest har-
monic in the spectrum, but for ADCs where the har-
monics are buried in the noise floor, it will be a noise
peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequen-
cies, fa and fb, any active device with nonlinearities
will create distortion products at sum and difference
frequencies of mfa ± nfb where m, n = 0, 1, 2, 3,
etc. Intermodulation distortion terms are those for
which neither m nor n are equal to zero. For example,
the second order terms include (fa + fb) and (fa – fb),
while the third order terms include (2fa + fb), (2fa –
fb), (fa + 2fb) and (fa – 2fb).
The AD7994/AD7993 is tested using the CCIF stan-
dard where two input frequencies near the top end of
the input bandwidth are used. In this case, the second
order terms are usually distanced in frequency from
the original sine waves while the third order terms are
usually at a frequency close to the input frequencies.
As a result, the second and third order terms are speci-
fied separately. The calculation of the intermodulation
distortion is as per the THD specification where it is
the ratio of the rms sum of the individual distortion
products to the rms amplitude of the sum of the funda-
mentals expressed in dBs.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7993BRU-0 | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7993 | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7994 | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7993BRU-1 | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7997 | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7994BRU-1REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 12-bit Serial 16-Pin TSSOP T/R |
| AD7994BRUZ0 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7994BRUZ-0 | 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7994BRUZ-0REEL | 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7994BRUZ-1 | 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。