- 您現在的位置：買賣IC網 > PDF目錄373927 > AD7994BRU-1 (ANALOG DEVICES INC) 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP PDF資料下載
參數資料
| 型號： | AD7994BRU-1 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| 中文描述： | 4-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | MO-153-AB, TSSOP-16 |
| 文件頁數： | 25/27頁 |
| 文件大小： | 277K |
| 代理商： | AD7994BRU-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁
AD7994/AD7993
–25–
REV. PrF
PRELIMINARY TECHNICAL DATA
Mode 2 -
This mode allows a conversion to be automatically initi-
ated anytime a read operation occurs. In order to use this
mode the command bits C4 - C1 in the Address Pointer
Byte shown in Table II must be programmed.
To select a particular Analog input for conversion in this
mode, then the user must set the corresponding channel
command bit to 1 in the Address Pointer Byte, see Table
XIII. When all four command bits are 0 then this mode is
not in use. A sequence can also be set up for this mode, if
more than one of the command bit in the Address Pointer
Byte are set. The ADC will start converting on the lowest
channel in the sequence and then the next lowest until all
the channels in the sequence have been converted on.
Figure 13 illustrates a two byte read operation from the
Conversion Result Register. This operation would nor-
mally be preceded by a write to the Address Pointer Regis-
ter so that the following read will access the desired
register, in this case the Conversion Result Register Fig-
ure 10. When the contents of the Address Pointer Register
are being loaded, if the command bits C4 to C1 are set
then the AD7994/AD7993 will begin to power up and
convert upon the selected channel(s), power-up will begin
on the fifth SCL falling edge of the Address Point Byte,
see point A Figure 17. Table XIII shows the channel se-
lection in this mode via the command bits, C4 to C1 in
the Address Pointer Register. The wake-up and conversion
time together should take approximately 3
μ
s. Following
this, the AD7994/AD7993 must be addressed again to tell
it that a read operation is required. The read then takes
place from the Conversion Result register. This read will
access the result from the conversion selected via the com-
mand bits. If the Command bits C2, C1 were set to 1,1,
then a four byte read would be necessary. The first read
accesses the data from the conversion on V
IN
1. While this
read takes place, a conversion occurs on V
IN
2. The second
read will access this data from V
IN
2. Figure 18 illustrates
how this mode operates.
When operating the AD7994-1/AD7993-1 in Mode2 with
Hs-Mode, 3.4 MHz SCL, the conversion may not be
complete before the master tries to read the conversion
result, if this is the case the AD7994-1/AD7993-1 will
hold the SCL line low after the read address during the
ACK clock, until the conversion is complete. When the
conversion is complete the AD7994-1/AD7993-1 will
release the SCL line and the master can then read the
conversion result.
Table XIII Address Pointer Byte
C4 C3 C2 C1
P3 P2 P1 P0
Analog Input Channel
0
0
0 0
0 0 0 0
Mode 2 not selected
0
0
0 1
0 0 0 0
Mode 2 Convert on V
IN
1
Mode 2 Convert on V
IN
2
Mode 2 Sequence between V
IN
1 and V
IN
2
Mode 2 Convert on V
IN
3
Mode 2 Sequence between V
IN
1 and V
IN
3
Mode 2 Sequence between V
IN
2 and V
IN
3
Mode 2 Sequence between V
IN
1, V
IN
2 and V
IN
3
Mode 2 Convert on V
IN
4
Mode 2 Sequence between V
IN
1 and V
IN
4
Mode 2 Sequence between V
IN
2 and V
IN
4
Mode 2 Sequence between V
IN
1, V
IN
2 and V
IN
4
Mode 2 Sequence between V
IN
3 and V
IN
4
Mode 2 Sequence between V
IN
1, V
IN
3 and V
IN
4
Mode 2 Sequence between V
IN
2, V
IN
3 and V
IN
4
Mode 2 Sequence between V
IN
1, V
IN
2, V
IN
3 and V
IN
4
0
0
1 0
0 0 0 0
0
0
1 1
0 0 0 0
0
1
0 0
0 0 0 0
0
1
0 1
0 0 0 0
0
1
1 0
0 0 0 0
0
1
1 1
0 0 0 0
1
0
0 0
0 0 0 0
1
0
0 1
0 0 0 0
1
0
1 0
0 0 0 0
1
0
1 1
0 0 0 0
1
1
0 0
0 0 0 0
1
1
0 1
0 0 0 0
1
1
1 0
0 0 0 0
1
1
1 1
0 0 0 0
With the pointer bits set to all 0’s then the next read will
access the results of the conversion Result Register.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7993BRU-0 | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7993 | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7994 | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7993BRU-1 | 4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7997 | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7994BRU-1REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 12-bit Serial 16-Pin TSSOP T/R |
| AD7994BRUZ0 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7994BRUZ-0 | 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7994BRUZ-0REEL | 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7994BRUZ-1 | 功能描述:IC ADC 12BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。