- 您現在的位置：買賣IC網 > PDF目錄373930 > AD8030ARJ-REEL7 (ANALOG DEVICES INC) Low Power, High Speed Rail-to-Rail Input/Output Amplifier PDF資料下載
參數資料
| 型號： | AD8030ARJ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Low Power, High Speed Rail-to-Rail Input/Output Amplifier |
| 中文描述： | DUAL OP-AMP, 6000 uV OFFSET-MAX, PDSO8 |
| 封裝： | MO-178BA, SOT-23, 8 PIN |
| 文件頁數： | 18/20頁 |
| 文件大小： | 649K |
| 代理商： | AD8030ARJ-REEL7 |
AD8029/AD8030/AD8040
CIRCUIT CONSIDERATIONS
PCB Layout
High speed op amps require careful attention to PCB layout to
achieve optimum performance. Particular care must be
exercised to minimize lead lengths of the bypass capacitors.
Excess lead inductance can influence the frequency response
and even cause high frequency oscillations. Using a multilayer
board with an internal ground plane can help reduce ground
noise and enable a more compact layout.
Rev. A | Page 18 of 20
To achieve the shortest possible trace length at the inverting
input, the feedback resistor, R
F
, should be located the shortest
distance from the output pin to the input pin. The return node
of the resistor R
G
should be situated as close as possible to the
return node of the negative supply bypass capacitor.
On multilayer boards, all layers beneath the op amp should be
cleared of metal to avoid creating parasitic capacitive elements.
This is especially true at the summing junction, i.e., the inver-
ting input, –IN. Extra capacitance at the summing junction can
cause increased peaking in the frequency response and lower
phase margin.
Grounding
To minimize parasitic inductances and ground loops in high
speed, densely populated boards, a ground plane layer is critical.
Understanding where the current flows in a circuit is critical in
the implementation of high speed circuit design. The length of
the current path is directly proportional to the magnitude of the
parasitic inductances and thus the high frequency impedance of
the path. Fast current changes in an inductive ground return
will create unwanted noise and ringing.
The length of the high frequency bypass capacitor pads and
traces is critical. A parasitic inductance in the bypass grounding
works against the low impedance created by the bypass
capacitor. Because load currents flow from supplies as well as
from ground, the load should be placed at the same physical
location as the bypass capacitor ground. For large values of
capacitors, which are intended to be effective at lower
frequencies, the current return path length is less critical.
Power Supply Bypassing
Power supply pins are actually inputs to the op amp. Care must
be taken to provide the op amp with a clean, low noise dc
voltage source.
Power supply bypassing is employed to provide a low imped-
ance path to ground for noise and undesired signals at all
frequencies. This cannot be achieved with a single capacitor
type; but with a variety of capacitors in parallel the bandwidth
of power supply bypassing can be greatly extended. The bypass
capacitors have two functions:
1.
Provide a low impedance path for noise and undesired
signals from the supply pins to ground.
2.
Provide local stored charge for fast switching conditions
and minimize the voltage drop at the supply pins during
transients. This is typically achieved with large electrolytic
capacitors.
Good quality ceramic chip capacitors should be used and
always kept as close as possible to the amplifier package. A
parallel combination of a 0.1 μF ceramic and a 10 μF electrolytic
covers a wide range of rejection for unwanted noise. The 10 μF
capacitor is less critical for high frequency bypassing and, in
most cases, one per supply line is sufficient. The values of
capacitors are circuit-dependant and should be determined by
the system’s requirements.
DESIGN TOOLS AND TECHNICAL SUPPORT
Analog Devices is committed to the design process by providing
technical support and online design tools. ADI offers technical
support via free evaluation boards, sample ICs, Spice models,
support—all available at www.analog.com
.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8030 | Low Power, High Speed Rail-to-Rail Input/Output Amplifier |
| AD8030AR | Low Power, High Speed Rail-to-Rail Input/Output Amplifier |
| AD8030AR-REEL | Low Power, High Speed Rail-to-Rail Input/Output Amplifier |
| AD8030AR-REEL7 | Low Power, High Speed Rail-to-Rail Input/Output Amplifier |
| AD8040 | Low Power, High Speed Rail-to-Rail Input/Output Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8030ARJZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O ±6V/12V 8-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:LOW-POWER HIGH-SPEED RAIL-TO-RAIL INPUT/OUTPUT OP AMPLIFIER - Tape and Reel |
| AD8030ARJZ-REEL | 功能描述:IC AMP GP R-R DUAL LP SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| AD8030ARJZ-REEL7 | 功能描述:IC AMP GP R-R DUAL LP SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| AD8030ARJZ-REEL7 | 制造商:Analog Devices 功能描述:IC OP-AMP 125MHZ 62V/ SOT-23-8 制造商:Analog Devices 功能描述:IC, OP-AMP, 125MHZ, 62V/s, SOT-23-8 |
| AD8030AR-REEL | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O ±6V/12V 8-Pin SOIC N T/R |
發布緊急采購，3分鐘左右您將得到回復。