- 您現在的位置：買賣IC網 > PDF目錄373931 > AD8036AR-REEL7 (ANALOG DEVICES INC) Low Distortion, Wide Bandwidth Voltage Feedback Clamp Amps PDF資料下載
參數資料
| 型號： | AD8036AR-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Low Distortion, Wide Bandwidth Voltage Feedback Clamp Amps |
| 中文描述： | OP-AMP, 11000 uV OFFSET-MAX, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 20/23頁 |
| 文件大小： | 387K |
| 代理商： | AD8036AR-REEL7 |
REV. A
–20–
AD8036/AD8037
Figure 80. Full-Wave Rectifier Scope
Thus for either positive or negative input signals, the output is
unity times the absolute value of the input signal. The circuit
can be easily configured to produce the negative absolute value
of the input by applying the input to V
H
instead of V
L
.
The circuit can get to within about 40 mV of ground during the
time when the input crosses zero. This voltage is fixed over a
wide frequency range and is a result of the switching between
the conventional op amp input and the clamp input. But be-
cause there are no diodes to rapidly switch from forward to re-
verse bias, the performance far exceeds that of diode based full
wave rectifiers.
The 40 mV offset mentioned can be removed by adding an off-
set to the circuit. A 27.4 k
input resistor to the inverting input
will have a gain of 0.01, while changing the gain of the circuit by
only 1%. A plus or minus 4 V dc level (depending on the polar-
ity of the rectifier) into this resistor will compensate for the
offset.
Full wave rectifiers are useful in many applications including
AM signal detection, high frequency ac voltmeters and various
arithmetic operations.
Amplitude Modulator
In addition to being able to be configured as an amplitude de-
modulator (AM detector), the AD8037 can also be configured
as an amplitude modulator as shown in Figure 81.
CARRIER IN
V
H
AM OUT
MODULATION IN
+5V
R
F
274
V
–5V
100
V
V
H
V
L
0.1
m
F
10
m
F
AD8037
0.1
m
F
10
m
F
R
G
274
V
Figure 81. Amplitude Modulator
The positive input of the AD8037 is driven with a square wave
of sufficient amplitude to produce clamping action at both the
high and low levels. This is the higher frequency carrier signal.
The modulation signal is applied to both the input of a unity
gain inverting amplifier and to V
L
, the lower clamping input.
V
H
is biased at +0.5 V dc.
To understand the circuit operation, it is helpful to first con-
sider a simpler circuit. If both V
L
and
V
H
were dc biased at
–0.5 V and the carrier and modulation inputs driven as above,
the output would be a 2 V p-p square wave at the carrier fre-
quency riding on a waveform at the modulating frequency. The
inverting input (modulation signal) is creating a varying offset to
the 2 V p-p square wave at the output. Both the high and low
levels clamp at twice the input levels on the clamps because the
noise gain of the circuit is two.
When V
L
is driven by the modulation signal instead of being
held at a dc level, a more complicated situation results. The re-
sulting waveform is composed of an upper envelope and a lower
envelope with the carrier square wave in between. The upper
and lower envelope waveforms are 180
°
out of phase as in a
typical AM waveform.
The upper envelope is produced by the upper clamp level being
offset by the waveform applied to the inverting input. This offset
is the opposite polarity of the input waveform because of the
inverting configuration.
The lower envelope is produced by the sum of two effects. First,
it is offset by the waveform applied to the inverting input as in
the case of the simplified circuit above. The polarity of this off-
set is in the same direction as the upper envelope. Second, the
output is driven in the opposite direction of the offset at twice
the offset voltage by the modulation signal being applied to V
L
.
This results from the noise gain being equal to two, and since
there is no inversion in this connection, it is opposite polarity
from the offset.
The result at the output for the lower envelope is the sum of
these two effects, which produces the lower envelope of an am-
plitude modulated waveform. See Figure 82.
Figure 82. AM Waveform
The depth of modulation can be modified in this circuit by
changing the amplitude of the modulation signal. This changes
the amplitude of the upper and lower envelope waveforms.
The modulation depth can also be changed by changing the dc
bias applied to V
H
. In this case the amplitudes of the upper and
lower envelope waveforms stay constant, but the spacing be-
tween them changes. This alters the ratio of the envelope ampli-
tude to the amplitude of the overall waveform.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8037AR-REEL | Low Distortion, Wide Bandwidth Voltage Feedback Clamp Amps |
| AD803 | Clock Recovery and Data Retiming Phase-Locked Loop(時鐘恢復和重定時PLL) |
| AD8041AR-REEL | 160 MHz Rail-to-Rail Amplifier with Disable |
| AD8041 | 160 MHz Rail-to-Rail Amplifier with Disable |
| AD8041-EB | 160 MHz Rail-to-Rail Amplifier with Disable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8036ARZ | 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD8036ARZ | 制造商:Analog Devices 功能描述:IC OP-AMP 240MHZ 1200V/ SOIC-8 |
| AD8036ARZ-REEL | 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| AD8036ARZ-REEL7 | 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| AD8036-EB | 功能描述:BOARD EVAL FOR AD8036 RoHS:否 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。