- 您現在的位置：買賣IC網 > PDF目錄373940 > AD8189ARUZ-R7 (ANALOG DEVICES INC) 350 MHz Single-Supply (5 V) Triple 2:1 Multiplexers PDF資料下載
參數資料
| 型號： | AD8189ARUZ-R7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 350 MHz Single-Supply (5 V) Triple 2:1 Multiplexers |
| 中文描述： | TRIPLE 1-CHANNEL, VIDEO MULTIPLEXER, PDSO24 |
| 封裝： | LEAD FREE, MO-153AD, TSSOP-24 |
| 文件頁數： | 17/24頁 |
| 文件大小： | 725K |
| 代理商： | AD8189ARUZ-R7 |
AD8188/AD8189
APPLICATIONS
SINGLE-SUPPLY OPERATION
The AD8188/AD8189 are targeted mainly for use in single-
supply 5 V systems. For operating on these supplies, both V
EE
and D
GND
should be tied to ground, and the control logic pins
should be referenced to ground. Normally, the DV
CC
supply
needs to be set to the same positive supply as the driving logic.
For dc-coupled, single-supply operation, it is necessary to set an
appropriate input dc level that is within the specified range of the
amplifier. For the unity-gain AD8188, the output dc level is the
same as the input, while for the gain-of-two AD8189, the V
REF
input can be biased to obtain an appropriate output dc level.
Figure 53 shows a circuit that provides a gain-of-two and is
dc-coupled. The video input signals must have a dc bias from
their source of approximately 1.5 V. This same voltage is applied
to V
REF
of the AD8189. The result is that when the video signal
is at 1.5 V, the output is also at the same voltage. This is close to
the lower dynamic range of both the input and the output.
When the input goes most positive, which is 700 mV above the
black level for a standard video signal, it reaches a value of 2.2 V,
and there is enough headroom for the signal. On the output
side, the magnitude of the signal changes by 1.4 V, making the
maximum output voltage 2.2 V + 1.4 V = 3.6 V. This is just
within the dynamic range of the output of the part.
AC-COUPLING
AD8188
When a video signal is ac-coupled, the amount of dynamic
range required to handle the signal can potentially be double
the amount required for dc-coupled operation. For the unity-
gain AD8188, there is still enough dynamic range to handle an
ac-coupled, standard video signal with 700 mV p-p amplitude.
Rev. 0 | Page 17 of 24
If the input is biased at 2.5 V dc, the input signal can potentially
go 700 mV both above and below this point. The resulting 1.8 V
and 2.2 V are within the input signal range for single 5 V
operation. Because the part is unity-gain, the outputs follow the
inputs, and there is adequate range at the output as well.
When the AD8188 is operated from a single supply of 5 V and
ground, ac-coupling is often useful. This is particularly true when
the input signals are a typical RGB source from a PC. These
signals go all the way to ground at the most negative, outside of
the AD8188 input range, when its negative supply is ground.
The closest that the input can go to ground is typically 1.3 V.
There are several basic methods for ac-coupling the inputs.
They all consist of a series capacitor followed by a circuit for
setting the dc operating point of the input and then the AD8188
input. If a termination is provided, it should be located before
the series coupling capacitor.
The different circuits vary in the means used to establish the dc
operating point after the coupling capacitor. A straightforward
way to do this is to use a voltage divider for each input.
However, because there are six inputs altogether, 12 resistors are
required to set all of the dc operating points. This means many
components in a small space, but the circuit has the advantage
of having the lowest crosstalk among any of the inputs. This
circuit is shown in Figure 54.
A circuit that uses the minimum number of resistors can be
designed. First, create a node, V
MID
, which serves as the bias
voltage for all of the inputs. Then, a single resistor is used to
connect from each input (inside the ac-coupling capacitor) and
V
MID
(see Figure 55).
V
EE
D
GND
RED
GRN
BLU
REDA
GRNA
BLUA
IN2B
IN1B
IN0B
IN0A
IN1A
IN2A
V
REF
5V
1.5V
1.5k
3.48k
BLUB
GRNB
REDB
DV
CC
SEL A/B
OE
×2
OUT0
OUT1
OUT2
V
CC
×2
×2
0.7V MAX
BLACK
LEVEL
LEVEL
2.2V
1.5V
TYPICAL INPUT LEVELS
(ALL 6 OUTPUTS)
TYPICAL OUTPUT LEVELS
(ALL 3 OUTPUTS)
3.0V
1.4V
MAX
1.5V
AD8189
3V TO 5V
5V
0
Figure 53. AD8189 DC-Coupled (Bypassing and Logic Not Shown)
相關PDF資料 |
PDF描述 |
|---|---|
| AD8189ARUZ-RL | 350 MHz Single-Supply (5 V) Triple 2:1 Multiplexers |
| AD8189Z-EVALZ | 350 MHz Single-Supply (5 V) Triple 2:1 Multiplexers |
| AD8188 | 350 MHz Single-Supply (5 V) Triple 2:1 Multiplexers |
| AD8188ARUZ | 350 MHz Single-Supply (5 V) Triple 2:1 Multiplexers |
| AD8188ARUZ-R7 | 350 MHz Single-Supply (5 V) Triple 2:1 Multiplexers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8189ARUZ-RL | 功能描述:IC MULTIPLEXER TRPL 2X1 24TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:1,000 系列:- 功能:多路復用器 電路:1 x 4:1 導通狀態電阻:- 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±5V 電流 - 電源:7mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| AD8189Z-EVALZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:350 MHz Single-Supply (5 V) Triple 2:1 Multiplexers |
| AD818AN | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk 制造商:Analog Devices 功能描述:IC AMP VIDEO LOW POWER DIP8 818 |
| AD818AN | 制造商:Analog Devices 功能描述:SEMICONDUCTORSLINEAR |
| AD818ANZ | 功能描述:IC VIDEO OPAMP 130MHZ LP 8-DIP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。