欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD8322-EVAL
廠商: Analog Devices, Inc.
英文描述: 5 V CATV Line Driver Coarse Step Output Power Control
中文描述: 5伏粗有線電視線路驅動器輸出功率控制步
文件頁數: 7/16頁
文件大小: 243K
代理商: AD8322-EVAL
REV. 0
AD8322
–7–
APPLICATIONS
General Application
The AD8322 is primarily intended for use as the upstream power
amplifier (PA) in DOCSIS (Data Over Cable Service Interface
Specifications) certified cable modems and CATV set-top boxes.
Upstream data is modulated in QPSK or QAM format. This is
done with DSP or a dedicated QPSK/QAM modulator. The
amplifier receives its input signal from the QPSK/QAM modula-
tor or from a DAC. In either case the signal must be low-pass
filtered before being applied to the amplifier. Because the distance
from the cable modem to the central office will vary with each
subscriber, the AD8322 must be capable of varying its output
power by applying gain or attenuation to ensure that all signals
arriving at the central office are of the same amplitude. The
upstream signal path contains components such as a transformer
and diplexer that will result in some amount of power loss. There-
fore, the amplifier must be capable of providing enough power
into a 75
load to overcome these losses without sacrificing the
integrity of the output signal.
Operational Description
The AD8322 is composed of three analog functions in the power-
up or forward mode. The input amplifier (preamp) can be used
single-ended or differentially. If the input is used in the differen-
tial configuration, it is imperative that the input signals be 180
degrees out of phase and of equal amplitudes. This will ensure
the proper gain accuracy and harmonic performance. The preamp
stage drives a DAC, which provides the bulk of the AD8322’s
attenuation (7 bits or 42.14 dB). The signals in the preamp and
DAC gain blocks are differential to improve the PSRR and linear-
ity. A differential current is fed from the DAC into the output
stage, which amplifies these currents to the appropriate levels
necessary to drive a 75
load. The output stage utilizes negative
feedback to implement a differential 75
output impedance.
This eliminates the need for external matching resistors.
SPI Programming and Gain Adjustment
Gain programming of the AD8322 is accomplished using a serial
peripheral interface (SPI) and three digital control lines,
DATEN
,
SDATA, and CLK. To change the gain, eight bits of data are
streamed into the serial shift register through the SDATA port.
The SDATA load sequence begins with a falling edge on the
DATEN
pin, thus activating the CLK line. Although the CLK
line is now activated, no change in gain is observed. With the
CLK line activated, data on the SDATA line is clocked into the
serial shift register, Most Significant Bit (MSB) first, on the
rising edge of each CLK pulse. A rising edge on the
DATEN
line
latches the contents of the shift register into the attenuator core
resulting in a well-controlled change in the output signal level.
The serial interface timing for the AD8322 is shown in Fig-
ures 2 and 3. The programmable gain range of the AD8322 is
–12.64 dB to +29.5 dB and scales 6.02 dB for each major carry.
Because the AD8322 was characterized with a TOKO transformer,
the stated gain values already take into account the losses asso-
ciated with the transformer. Valid gain codes are the major carries
from decimal 1–128 (decimal values 1, 2, 4, 8, 16, 32, 64, 128).
The resulting gain for each code can be seen in Table I. Although
the AD8322 is designed for use with the previous eight codes,
the intermediate codes can be used.
The gain transfer function is as follows:
A
V
= 20
×
LOG (0.2332
×
CODE) for 1
CODE
128
A
V
= 29.5 dB for CODE
128
where
A
V
is the gain in dB and
CODE
is the decimal equivalent
of the 8-bit word.
Figure 4 shows the gain characteristic for all possible values
(except 0) in an 8-bit word. Code 0 may be used if more
feedthrough isolation is required. It typically provides –85 dB of
isolation across the 5 MHz to 65 MHz upstream band.
GAIN CODE
Decimal
35
0
G
30
25
20
15
10
0
5
10
15
20
32
64
96
128
160
192
224
256
5
Figure 4. Gain vs. Gain Code
Input Bias, Impedance, and Termination
The V
IN+
and V
IN–
inputs have a dc bias level of approximately
V
CC
/2, therefore the input signal should be ac-coupled. The
differential input impedance is approximately 235
while the
single-ended input impedance is 210
. If the AD8322 is being
operated in a single-ended input configuration with a desired
input impedance of 75
, the V
IN+
and V
IN–
inputs should be
terminated as shown in Figure 5. For input impedances other
than 75
, the value of R1 in Figure 5 can be calculated using
the following equation:
Z
R
IN
=
1210
Z
IN
= 75
AD8322
R1 = 118
Figure 5. Single-Ended Input Termination
相關PDF資料
PDF描述
AD8322ARU 5 V CATV Line Driver Coarse Step Output Power Control
AD8322 5 V CATV Line Driver Coarse Step Output Power Control
AD8323ARU-REEL 5 V CATV Line Driver Fine Step Output Power Control
AD8323ARU 5 V CATV Line Driver Fine Step Output Power Control
AD8323 5 V CATV Line Driver Fine Step Output Power Control
相關代理商/技術參數
參數描述
AD8323 制造商:AD 制造商全稱:Analog Devices 功能描述:5 V CATV Line Driver Fine Step Output Power Control
AD8323ARU 制造商:Analog Devices 功能描述:SP Amp Line Driver Amp Single 5.25V 28-Pin TSSOP Tube 制造商:Rochester Electronics LLC 功能描述:TSSOP FINE STEP +5V CATV LINE DRIVER - Bulk
AD8323ARU-REEL 制造商:Analog Devices 功能描述:SP Amp Line Driver Amp Single 5.25V 28-Pin TSSOP T/R 制造商:Rochester Electronics LLC 功能描述:TSSOP FINE STEP +5V CATV LINE DRIVER - Tape and Reel
AD8323ARUZ 制造商:Analog Devices 功能描述:SP Amp Line Driver Amp Single 5.25V 28-Pin TSSOP Tube 制造商:Rochester Electronics LLC 功能描述:TSSOP FINE STEP +5V CATV LINE DRIVER - Bulk
AD8323ARUZ-REEL 制造商:Analog Devices 功能描述:SP Amp Line Driver Amp Single 5.25V 28-Pin TSSOP T/R 制造商:Rochester Electronics LLC 功能描述:TSSOP FINE STEP +5V CATV LINE DRIVER - Tape and Reel
主站蜘蛛池模板: 湘西| 理塘县| 沾化县| 遂宁市| 囊谦县| 万安县| 呼玛县| 闻喜县| 湛江市| 常熟市| 耿马| 嘉善县| 双流县| 萍乡市| 疏勒县| 泸西县| 黄平县| 汶川县| 武穴市| 汨罗市| 会泽县| 陕西省| 安图县| 和林格尔县| 安丘市| 凤城市| 汾阳市| 嘉荫县| 南溪县| 成武县| 河间市| 四会市| 银川市| 周口市| 洪江市| 辛集市| 恩平市| 全州县| 镶黄旗| 清新县| 页游|