- 您現在的位置：買賣IC網 > PDF目錄373950 > AD8571ARM (ANALOG DEVICES INC) Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifiers PDF資料下載
參數資料
| 型號： | AD8571ARM |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifiers |
| 中文描述： | OP-AMP, 10 uV OFFSET-MAX, 1 MHz BAND WIDTH, PDSO8 |
| 封裝： | MSOP-8 |
| 文件頁數： | 16/19頁 |
| 文件大小： | 247K |
| 代理商： | AD8571ARM |
AD8571/AD8572/AD8574
–16–
REV. 0
A High Accuracy Thermocouple Amplifier
Figure 58 shows a K-type thermocouple amplifier configuration
with cold-junction compensation. Even from a 5 V supply, the
AD8571 can provide enough accuracy to achieve a resolution
of better than 0.02
°
C from 0
°
C to 500
°
C. D1 is used as a tempera-
ture measuring device to correct the cold-junction error from
the thermocouple and should be placed as close as possible to
the two terminating junctions. With the thermocouple measuring
tip immersed in a zero-degree ice bath, R
6
should be adjusted
until the output is at 0 V.
Using the values shown in Figure 58, the output voltage will
track temperature at 10 mV/
°
C. For a wider range of tempera-
ture measurement, R
9
can be decreased to 62 k
. This will
create a 5 mV/
°
C change at the output, allowing measurements
of up to 1000
°
C.
AD8571
3
8
4
0V TO 5V
(0
8
C TO 500
8
C)
5V
0.1
m
F
+
10
m
F
REF02EZ
0.1
m
F
12V
2
6
4
+
+
–
–
D1
1N4148
5V
K-TYPE
THERMOCOUPLE
40.7
m
V/
8
C
1
R
6
200
V
R
4
5.62k
V
R
9
124k
V
R
53.6
V
R
40.2k
V
R
8
453
V
R
1
10.7k
V
2
R
2
2.74k
V
Figure 58. A Precision K-Type Thermocouple Amplifier
with Cold-Junction Compensation
Precision Current Meter
Because of its low input bias current and superb offset voltage at
single supply voltages, the AD857x is an excellent amplifier for
precision current monitoring. Its rail-to-rail input allows the
amplifier to be used as either a high-side or low-side current
monitor. Using both amplifiers in the AD8572 provides a simple
method to monitor both current supply and return paths for
load or fault detection.
Figure 59 shows a high-side current monitor configuration. Here,
the input common-mode voltage of the amplifier will be at or near
the positive supply voltage. The amplifier’s rail-to-rail input provides
a precise measurement, even with the input common-mode voltage
at the supply voltage. The CMOS input structure does not draw any
input bias current, ensuring a minimum of measurement error.
The 0.1
resistor creates a voltage drop to the noninverting
input of the AD857x. The amplifier’s output is corrected until
this voltage appears at the inverting input. This creates a current
through R
1
, which in turn flows through R
2
. The Monitor Output
is given by:
Monitor Output
R
R
R
I
SENSE
L
=
×
×
2
1
(23)
Using the components shown in Figure 59, the Monitor Output
transfer function is 2.5V/A.
Figure 60 shows the low-side monitor equivalent. In this circuit,
the input common-mode voltage to the AD8572 will be at or near
ground. Again, a 0.1
resistor provides a voltage drop proportional
to the return current. The output voltage is given as:
V
V
R
R
R
I
OUT
SENSE
L
=
+
×
×
2
1
(24)
For the component values shown in Figure 60, the output transfer
function decreases from V at –2.5 V/A.
8
1
4
3
3V
0.1
m
F
R
0.1
V
V+
I
L
G
S
D
2
M1
Si9433
MONITOR
OUTPUT
3V
1/2
AD8572
R
1
100
V
R
2.49k
V
Figure 59. A High-Side Load Current Monitor
V+
RETURN TO
GROUND
1/2 AD8572
V+
V
OUT
Q1
R
2.49k
V
R
1
100
V
R
0.1
V
Figure 60. A Low-Side Load Current Monitor
Precision Voltage Comparator
The AD857x can be operated open-loop and used as a precision
comparator. The AD857x has less than 50
μ
V of offset voltage
when run in this configuration. The slight increase of offset
voltage stems from the fact that the autocorrection architecture
operates with lowest offset in a closed-loop configuration, that
is, one with negative feedback. With 50 mV of overdrive, the
device has a propagation delay of 15
μ
s on the rising edge and
8
μ
s on the falling edge.
Care should be taken to ensure the maximum differential volt-
age of the device is not exceeded. For more information, please
refer to the section on Input Overvoltage Protection.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8582CHIPS | +5 Volt, Parallel Input Complete Dual 12-Bit DAC |
| AD8582AN | +5 Volt, Parallel Input Complete Dual 12-Bit DAC |
| AD8582AR | +5 Volt, Parallel Input Complete Dual 12-Bit DAC |
| AD8591 | CMOS Single Supply Rail-to-Rail Input/Output Operational Amplifiers with Shutdown |
| AD8591ART | CMOS Single Supply Rail-to-Rail Input/Output Operational Amplifiers with Shutdown |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8571ARM-R2 | 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Single R-R I/O 5V 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:DUAL PRECISION RAIL-RAIL CHOPPER OPAMP - Bulk |
| AD8571ARM-REEL | 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Single R-R I/O 5V 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:DUAL PRECISION RAIL-RAIL CHOPPER OPAMP - Tape and Reel |
| AD8571ARMZ | 功能描述:IC OPAMP CHOPPER R-R 30MA 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| AD8571ARMZ-R2 | 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Single R-R I/O 5V 8-Pin MSOP T/R |
| AD8571ARMZ-REEL | 功能描述:IC OPAMP CHOPPER R-R 30MA 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
發布緊急采購，3分鐘左右您將得到回復。