- 您現在的位置：買賣IC網 > PDF目錄373959 > AD9200KST (ANALOG DEVICES INC) Complete 10-Bit, 20 MSPS, 80 mW CMOS A/D Converter PDF資料下載
參數資料
| 型號： | AD9200KST |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Complete 10-Bit, 20 MSPS, 80 mW CMOS A/D Converter |
| 中文描述： | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| 封裝： | PLASTIC, LQFP-48 |
| 文件頁數： | 23/24頁 |
| 文件大小： | 338K |
| 代理商： | AD9200KST |
AD9200
–23–
REV. E
GROUNDING AND LAYOUT RULES
As is the case for any high performance device, proper ground-
ing and layout techniques are essential in achieving optimal
performance. The analog and digital grounds on the AD9200
have been separated to optimize the management of return
currents in a system. Grounds should be connected near the
ADC. It is recommended that a printed circuit board (PCB) of
at least four layers, employing a ground plane and power planes,
be used with the AD9200. The use of ground and power planes
offers distinct advantages:
1. The minimization of the loop area encompassed by a signal
and its return path.
2. The minimization of the impedance associated with ground
and power paths.
3. The inherent distributed capacitor formed by the power plane,
PCB insulation and ground plane.
These characteristics result in both a reduction of electro-
magnetic interference (EMI) and an overall improvement in
performance.
It is important to design a layout that prevents noise from cou-
pling onto the input signal. Digital signals should not be run in
parallel with the input signal traces and should be routed away
from the input circuitry. Separate analog and digital grounds
should be joined together directly under the AD9200 in a solid
ground plane. The power and ground return currents must be
carefully managed. A general rule of thumb for mixed signal
layouts dictates that the return currents from digital circuitry
should not pass through critical analog circuitry.
DIGITAL OUTPUTS
Each of the on-chip buffers for the AD9200 output bits
(D0–D9) is powered from the DRVDD supply pins, separate
from AVDD. The output drivers are sized to handle a variety
of logic families while minimizing the amount of glitch energy
generated. In all cases, a fan-out of one is recommended to keep
the capacitive load on the output data bits below the specified
20 pF level.
For DRVDD = 5 V, the AD9200 output signal swing is compat-
ible with both high speed CMOS and TTL logic families. For
TTL, the AD9200 on-chip, output drivers were designed to
support several of the high speed TTL families (F, AS, S). For
applications where the clock rate is below 20 MSPS, other TTL
families may be appropriate. For interfacing with lower voltage
CMOS logic, the AD9200 sustains 20 MSPS operation with
DRVDD = 3 V. In all cases, check your logic family data sheets
for compatibility with the AD9200 Digital Specification table.
THREE-STATE OUTPUTS
The digital outputs of the AD9200 can be placed in a high
impedance state by setting the THREE-STATE pin to HIGH.
This feature is provided to facilitate in-circuit testing or evaluation.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9200LQFP-EVAL | Complete 10-Bit, 20 MSPS, 80 mW CMOS A/D Converter |
| AD9200JRSRL | Complete 10-Bit, 20 MSPS, 80 mW CMOS A/D Converter |
| AD9200ARSRL | Complete 10-Bit, 20 MSPS, 80 mW CMOS A/D Converter |
| AD9200 | Complete 10-Bit, 20 MSPS, 80 mW CMOS A/D Converter |
| AD9200ARS | CAP 33 UF 16V 10% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9200KSTRL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel 制造商:Analog Devices 功能描述: |
| AD9200KSTZ | 制造商:Analog Devices 功能描述:ADC SGL PIPELINED 20MSPS 10-BIT PARALLEL 48LQFP - Trays |
| AD9200KSTZRL | 制造商:Analog Devices 功能描述:ADC SGL PIPELINED 20MSPS 10-BIT PARALLEL 48LQFP - Tape and Reel |
| AD9200LQFP-EVAL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 10-Bit, 20 MSPS, 80 mW CMOS A/D Converter |
| AD9200SSOP-EVAL | 制造商:Analog Devices 功能描述:Evaluation Board For AD9200 CMOS A/D Converter 制造商:Analog Devices 功能描述:EVAL BD FOR AD9200 CMOS A/D CNVRTR - Bulk |
發布緊急采購，3分鐘左右您將得到回復。