欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

<ul id="qu2iu"></ul>

<del id="qu2iu"></del>

您好，
買賣IC網歡迎您。
請登錄
免費注冊

您現在的位置：買賣IC網 > PDF目錄373962 > AD9281 (Analog Devices, Inc.) Dual Channel 8-Bit Resolution CMOS ADC PDF資料下載

參數資料

型號：	AD9281
廠商：	Analog Devices, Inc.
英文描述：	Dual Channel 8-Bit Resolution CMOS ADC
中文描述：	雙通道8位分辨率的CMOS模數轉換器
文件頁數：	8/19頁
文件大小：	406K
代理商：	AD9281

第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁

AD9281

–8–

REV. E

THEORY OF OPERATION

The AD9281 integrates two A/D converters, two analog input

buffers, an internal reference and reference buffer, and an out-

put multiplexer. For clarity, this data sheet refers to the two

converters as “I” and “Q.” The two A/D converters simulta-

neously sample their respective inputs on the rising edge of the

input clock. The two converters distribute the conversion opera-

tion over several smaller A/D sub-blocks, refining the conversion

with progressively higher accuracy as it passes the result from

stage to stage. As a consequence of the distributed conversion,

each converter requires a small fraction of the 256 comparators

used in a traditional flash-type 8-bit ADC. A sample-and-hold

function within each of the stages permits the first stage to oper-

ate on a new input sample while the following stages continue to

process previous samples. This results in a “pipeline processing”

latency of three clock periods between when an input sample is

taken and when the corresponding ADC output is updated into

the output registers.

The AD9281 integrates input buffer amplifiers to drive the

analog inputs of the converters. In most applications, these

input amplifiers eliminate the need for external op amps for the

input signals. The input structure is fully differential, but the

SHA common-mode response has been designed to allow the

converter to readily accommodate either single-ended or differ-

ential input signals. This differential structure makes the part

capable of accommodating a wide range of input signals.

The AD9281 also includes an on-chip bandgap reference and

reference buffer. The reference buffer shifts the ground-referred

reference to levels more suitable for use by the internal circuits

of the converter. Both converters share the same reference and

reference buffer. This scheme provides for the best possible gain

match between the converters while simultaneously minimizing

the channel-to-channel crosstalk.

Each A/D converter has its own output latch, which updates on

the rising edge of the input clock. A logic multiplexer, con-

trolled through the SELECT pin, determines which channel is

passed to the digital output pins. The output drivers have their

own supply, allowing the part to be interfaced to a variety of

logic families. The outputs can be placed in a high impedance

state using the CHIP SELECT pin.

The AD9281 has great flexibility in its supply voltage. The

analog and digital supplies may be operated from 2.7 V to 5.5 V,

independently of one another.

ANALOG INPUT

Figure 16 shows an equivalent circuit structure for the analog

input of one of the A/D converters. PMOS source-followers

buffer the analog input pins from the charge kickback problems

normally associated with switched capacitor ADC input struc-

tures. This produces a very high input impedance on the part,

allowing it to be effectively driven from high impedance sources.

This means that the AD9281 could even be driven directly by a

passive antialias filter.

ADC

CORE

+FS

LIMIT

–FS

LIMIT

BUFFER

IINA

IINB

REF

+FS LIMIT =

REF

REF/2

–FS LIMIT =

REF

–V

REF/2

OUTPUT

WORD

SHA

Figure 16. Equivalent Circuit for AD9281 Analog Inputs

The source followers inside the buffers also provide a level-shift

function of approximately 1 V, allowing the AD9281 to accept

inputs at or below ground. One consequence of this structure is

that distortion will result if the analog input comes within 1.4 V

of the positive supply. For optimum high frequency distortion

performance, the analog input signal should be centered accord-

ing to Figure 27.

The capacitance load of the analog input pin is 4 pF to the

analog supplies (AVSS, AVDD).

Full-scale setpoints may be calculated according to the following

algorithm (V

REF

may be internally or externally generated):

–F

= V

REF

– (V

REF

/2)

= V

REF

+ (V

REF

/2)

SPAN

= V

REF

10.0

0.0E+0

0.0

–10.0

–20.0

–30.0

–40.0

–50.0

–60.0

–70.0

–80.0

–90.0

–100.0

–110.0

2.0E+6

4.0E+6

6.0E+6

8.0E+6 10.0E+6 12.0E+6 14.0E+6

FUND

5TH

6TH

4TH7TH

3RD

9TH

2ND

8TH

Figure 15a. Simultaneous Operation of I and Q Channels