欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD9814
廠商: Analog Devices, Inc.
英文描述: LABELS,CABLE MARKERS,CABLE MARKERS,LABELS, CABLE MARKERS,WIRE IDENTIFICATION AND MARKING SYSTEMS,SHRINK TUBING LABELS ,KROY RoHS Compliant: NA
中文描述: 完整的14位防治荒漠化公約/ CIS信號處理器
文件頁數: 5/15頁
文件大小: 160K
代理商: AD9814
REV. 0
AD9814
–5–
DEFINITIONS OF SPECIFICATIONS
INTEGRAL NONLINEARITY (INL)
Integral nonlinearity error refers to the deviation of each indi-
vidual code from a line drawn from “zero scale” through “posi-
tive full scale.” The point used as “zero scale” occurs 1/2 LSB
before the first code transition. “Positive full scale” is defined as
a level 1 1/2 LSB beyond the last code transition. The deviation
is measured from the middle of each particular code to the true
straight line.
DIFFERENTIAL NONLINEARITY (DNL)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Thus every
code must have a finite width. No missing codes guaranteed to
14-bit resolution indicates that all 16384 codes, respectively,
must be present over all operating ranges.
OFFSET ERROR
The first ADC code transition should occur at a level 1/2 LSB
above the nominal zero scale voltage. The offset error is the
deviation of the actual first code transition level from the ideal
level.
GAIN ERROR
The last code transition should occur for an analog value
1 1/2 LSB below the nominal full-scale voltage. Gain error is
the deviation of the actual difference between first and last code
transitions and the ideal difference between the first and last
code transitions.
INPUT REFERRED NOISE
The rms output noise is measured using histogram techniques.
The ADC output codes’ standard deviation is calculated in
LSB, and converted to an equivalent voltage, using the relation-
ship 1 LSB = 4 V/16384 = 244 mV. The noise is then referred
to the input of the AD9814 by dividing by the PGA gain.
CHANNEL-TO-CHANNEL CROSSTALK
In an ideal three channel system, the signal in one channel will
not influence the signal level of another channel. The channel-
to-channel crosstalk specification is a measure of the change that
occurs in one channel as the other two channels are varied. In
the AD9814, one channel is grounded and the other two chan-
nels are exercised with full-scale input signals. The change in the
output codes from the first channel is measured and compared
with the result when all three channels are grounded. The differ-
ence is the channel-to-channel crosstalk, stated in LSB.
APERTURE DELAY
The aperture delay is the time delay that occurs from when a
sampling edge is applied to the AD9814 until the actual sample
of the input signal is held. Both CDSCLK1 and CDSCLK2
sample the input signal during the transition from high to low,
so the aperture delay is measured from each clock’s falling edge
to the instant the actual internal sample is taken.
POWER SUPPLY REJECTION
Power Supply Rejection specifies the maximum full-scale change
that occurs from the initial value when the supplies are varied
over the specified limits.
相關PDF資料
PDF描述
AD9814JR LABELS,CABLE MARKERS,CABLE MARKERS,LABELS, CABLE MARKERS,WIRE IDENTIFICATION AND MARKING SYSTEMS,SHRINK TUBING LABELS ,KROY RoHS Compliant: NA
AD9814KR Complete 14-Bit CCD/CIS Signal Processor
AD9816-EB Complete 12-Bit 6 MSPS CCD/CIS Signal Processor
AD9816JS Complete 12-Bit 6 MSPS CCD/CIS Signal Processor
AD9816JS-80010 Complete 12-Bit 6 MSPS CCD/CIS Signal Processor
相關代理商/技術參數
參數描述
AD9814-EB 制造商:Analog Devices 功能描述:- Bulk
AD9814JR 功能描述:IC CCD SIGNAL PROC 14BIT 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD9814JRRL 功能描述:IC CCD SIGNAL PROC 14BIT 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD9814KR 制造商:Analog Devices 功能描述:AFE Video 1ADC 14-Bit 5V 28-Pin SOIC W 制造商:Analog Devices 功能描述:14 BIT 6 MSPS SCANNER ANALOG FRONT END - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:14 BIT 6 MSPS SCANNER ANALOG FRONT END - Bulk
AD9814KRRL 制造商:Analog Devices 功能描述:AFE Video 1ADC 14-Bit 5V 28-Pin SOIC W 制造商:Analog Devices 功能描述:14 BIT 6 MSPS SCANNER ANALOG FRONT END - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:14 BIT 6 MSPS SCANNER ANALOG FRONT END - Bulk
主站蜘蛛池模板: 时尚| 合山市| 嘉义市| 如皋市| 惠来县| 精河县| 平乐县| 确山县| 汾西县| 筠连县| 炎陵县| 沁源县| 新河县| 确山县| 福海县| 鹰潭市| 蓝田县| 朔州市| 宁乡县| 阳春市| 沾益县| 绵竹市| 博客| 靖宇县| 胶州市| 华容县| 遂宁市| 高唐县| 平果县| 银川市| 格尔木市| 阜康市| 稻城县| 万宁市| 孟津县| 固镇县| 通渭县| 屯昌县| 九龙城区| 余庆县| 化德县|