- 您現在的位置：買賣IC網 > PDF目錄373968 > AD9842A (Analog Devices, Inc.) Complete 20 MSPS CCD Signal Processors PDF資料下載
參數資料
| 型號： | AD9842A |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Complete 20 MSPS CCD Signal Processors |
| 中文描述： | 完成20 MSPS的CCD信號處理器 |
| 文件頁數： | 22/23頁 |
| 文件大小： | 272K |
| 代理商： | AD9842A |
REV. 0
AD9841A/AD9842A
–22–
36
35
34
33
32
31
30
29
28
27
26
25
13 14 15 16 17 18 19 20 21 22 23 24
1
2
3
4
5
6
7
8
9
10
11
12
37
48 47 46 45 44
39 38
43 42 41 40
PIN 1
TOP VIEW
(Not to Scale)
AUX1IN
AVSS
AUX2IN
AVDD2
BYP4
NC
CCDIN
BYP2
BYP1
AVDD1
AVSS
AVSS
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
(MSB) D11
AD9842A
S
S
S
N
S
N
T
D
D
V
V
C
D
D
D
D
D
H
P
C
S
S
C
V
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
3V
ANALOG SUPPLY
CCD SIGNAL
3V
ANALOG SUPPLY
12
DATA
OUTPUTS
3
SERIAL
INTERFACE
0.1 F
1.0 F
1.0 F
0.1 F
3V
ANALOG SUPPLY
8
CLOCK
INPUTS
0.1 F
0.1 F
3V
ANALOG SUPPLY
3V
DRIVER
SUPPLY
NC = NO CONNECT
Figure 34. AD9842A Recommended Circuit Configuration for CCD-Mode
Internal Power-On Reset Circuitry
After power-on, the AD9842A will automatically reset all inter-
nal registers and perform internal calibration procedures. This
takes approximately 1 ms to complete. During this time, normal
clock signals and serial write operations may occur. However,
serial register writes will be ignored until the internal reset
operation is completed. Pin 43 (formerly RSTB on the AD9842A
non-A) is no longer used for the reset operation. Toggling Pin
43 in the AD9842A will have no effect.
Grounding and Decoupling Recommendations
As shown in Figures 33 and 34, a single ground plane is recom-
mended for the AD9841A/AD9842A. This ground plane should be
as continuous as possible, particularly around Pins 25 through
39. This will ensure that all analog decoupling capacitors provide
the lowest possible impedance path between the power and bypass
pins and their respective ground pins. All decoupling capaci-
tors should be located as close as possible to the package pins. A
single clean power supply is recommended for the AD9841A/AD9842A,
but a separate digital driver supply may be used for DRVDD
(Pin 13). DRVDD should always be decoupled to DRVSS (Pin
14), which should be connected to the analog ground plane.
Advantages of using a separate digital driver supply include using a
lower voltage (2.7 V) to match levels with a 2.7 V ASIC, reducing
digital power dissipation, and reducing potential noise coupling.
If the digital outputs (Pins 3–12) must drive a load larger than
20 pF, buffering is recommended to reduce digital code transi-
tion noise. Alternatively, placing series resistors close to the
digital output pins may also help reduce noise.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9841A | Complete 20 MSPS CCD Signal Processors |
| AD9841AJST | Trimmers; Series:T73; Resistance Tolerance: 10%; Power Rating:0.5W; Operating Temperature Range:-55 C to ? C; Resistor Element Material:Cermet; Voltage Rating:158.1V; Temperature Coefficient:100 ppm RoHS Compliant: Yes |
| AD9842AJST | Complete 20 MSPS CCD Signal Processors |
| AD9843A | Complete 10-Bit 20 MSPS CCD Signal Processor |
| AD9843AJST | Complete 10-Bit 20 MSPS CCD Signal Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9842AJST | 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3.3V 48-Pin LQFP 制造商:Analog Devices 功能描述:AFE VID 1ADC 10-BIT 3.3V 48LQFP - Trays 制造商:Rochester Electronics LLC 功能描述:12 BIT 20 MHZ ANALOG FRONT END - Tape and Reel |
| AD9842AJSTRL | 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3.3V 48-Pin LQFP T/R 制造商:Analog Devices 功能描述:AFE VID 1ADC 10-BIT 3.3V 48LQFP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:12 BIT 20 MHZ ANALOG FRONT END - Tape and Reel |
| AD9842AJSTZ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9842-EB | 制造商:Analog Devices 功能描述:12 BIT 20 MHZ ANALOG FRONT END - Bulk |
| AD9843A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 10-Bit 20 MSPS CCD Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。