欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD9862BST
廠商: ANALOG DEVICES INC
元件分類: 通信及網絡
英文描述: Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications
中文描述: SPECIALTY TELECOM CIRCUIT, PQFP128
封裝: PLASTIC, LQFP-128
文件頁數: 26/32頁
文件大小: 617K
代理商: AD9862BST
REV. 0
–26–
AD9860/AD9862
For the Normal Operation mode, the Tx timing is based on
a clock derived from the DLL output, while the Rx clock is
unaffected by the DLL setting.
The Alternative Operation mode, timing utilizes the output of
the DLL to generate both Rx and Tx clocks. It also sets default
operation of the DLL to 4 mode.
Normal Operation is typically recommended because the Rx ADC
is more sensitive to the jitter and noise that the DLL may gener-
ate, so its performance may degrade. The Mode/TxBlank pin
logic level at power up or RESET defines in which mode the
device powers up. If Mode/TxBlank is low at power up, the
Normal Operation mode is configured. Otherwise, the Alternative
Operation mode is configured.
Rx Path (Normal Operation)
The ADC sampling rate, the Rx data output rate, and the rate of
CLKOUT1 (clock used to latch output data) are the parameters
of interest for the receive path data. These parameters in addition
to the data bandwidth are related to CLKIN by decimation filters,
divide by two circuits, data multiplexer logic and retiming latches.
The Rx path timing can be broken into two separate relation-
ships: the ADC sample rate relative to the input clock, CLKIN
and the output data rate relative to CLKOUT1.
The ADCs sample rate relative to CLKIN is controlled by the
ADC Div2 register and the sample rate can be equal to or one half
of the input clock rate.
The output data relative to CLKOUT1 has many configurations
providing a flexible interface. The different options are shown in
Figure 8. Table Ia and Ib describe the setup required to obtain
the desired data timing. RxSync is available when the Rx data is
decimated and multiplexed to identify which channel data is
present at the output bus.
00: C = B
01: C = 2 B
10: C = 4 B
00: D = C
01: D = C/2
10: D = C/4
00: G = F
01: G = 2 F
10: G = 4 F
ADC SAMPLE RATE
(NOT TO EXCEED 64MHz)
DLL OUTPUT RATE
(NOT TO EXCEED 128MHz)
CLKOUT2
INPUT
Tx DATA RATE
TxDAC UPDATE RATE
EACH CHANNEL
(CANNOT EXCEED
DLL OUTPUT RATE)
B
E
G
DLL MULT
CLKOUT2 DIV
INTERP
0: E = D
1: E = 2 D
C
2 EDGES
F = E/2
D
DUAL CHANNEL
FACTOR
INPUT Tx DATA RATE
EACH CHANNEL
0: B = A
1: B = A/2
CLKIN
A
ADC DIV2
F
Figure 11. Dual Tx Timing Block Diagram, Alternative Operation
Tx DATA TIMING No. 1
f
Tx
= CLKOUT2
Tx DATA TIMING No. 2
f
Tx
= 2 CLKOUT2
f
T
1
f
T
2
f
T
3
f
T
4
f
CLKOUT2
Figure 12. Tx Timing Diagram
The Rx data (unless re-timed using the Rx Retime register) is
timed relative to the CLKOUT1 pin output. The Rx output data
can be decimated (halving the data rate) or both channels can be
multiplexed onto the channel A data bus (doubling the data rate).
Decimation enables oversampling while maintaining a slower
external data transfer rate and provides superior suppression of
out of band signals and noise. Multiplexing enables fewer digital
output bits to be used to transfer data from the Rx path to the
digital ASIC collecting the data.
When Mux Mode is enabled with an output data rate equal to
CLKOUT1 (Timing No. 3 in Figure 9) then the RxSync pin is
required to identify which channel
s output data is on the output
data bus. RxSync output is aligned with the output data, and by
default a logic low indicates data from Rx Channel B is currently
on the output data bus. If RxSync is logic high, then data from
Rx Channel A is currently on the output data bus. The Inv RxSync
register can be used to switch this notation.
The CLKOUT1 pin outputs a clock at the frequency of CLKIN or
CLKIN/2 depending on the voltage level applied to the CLKSEL
pin. If a logic low is applied to CLKSEL, CLKOUT1 will run
at half the CLKIN rate, if CLKSEL is set to logic high CLKOUT1
outputs a clock equal to CLKIN.
This timing flexibility along with the invert option for CLKOUT1,
controlled by the Inv 1 register allow for various methods of latch-
ing data from the Rx path to the digital ASIC, which will process
the data. These options are shown in Table Ia and Ib along with
a timing diagram in Figure 9. Not shown is the option to invert
CLKOUT1, controlled by the Inv 1 register. For this mode, relative
timing remains the same except the opposite edges of CLKOUT1
would be used.
相關PDF資料
PDF描述
AD9864 IF Digitizing Subsystem
AD9864-EB IF Digitizing Subsystem
AD9864BCPZ IF Digitizing Subsystem
AD9864BCPZRL IF Digitizing Subsystem
AD9866BCPRL Broadband Modem Mixed Signal Front End
相關代理商/技術參數
參數描述
AD9862BSTRL 制造商:Analog Devices 功能描述:Mixed Signal Front End 128-Pin LQFP T/R 制造商:Rochester Electronics LLC 功能描述:12B MIXED SIGNAL FRONT END MXFE PROCESSO - Tape and Reel
AD9862BSTZ 功能描述:IC FRONT-END MIXED-SGNL 128-LQFP RoHS:是 類別:RF/IF 和 RFID >> RF 前端 (LNA + PA) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- RF 型:GPS 頻率:1575.42MHz 特點:- 封裝/外殼:48-TQFP 裸露焊盤 供應商設備封裝:48-TQFP 裸露焊盤(7x7) 包裝:托盤
AD9862BSTZRL 功能描述:IC PROCESSOR FRONT END 128LQFP RoHS:是 類別:RF/IF 和 RFID >> RF 前端 (LNA + PA) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- RF 型:GPS 頻率:1575.42MHz 特點:- 封裝/外殼:48-TQFP 裸露焊盤 供應商設備封裝:48-TQFP 裸露焊盤(7x7) 包裝:托盤
AD9862-EB 制造商:Analog Devices 功能描述: 制造商:Analog Devices 功能描述:MIXED SIGNAL FRONT END - Bulk
AD9862-EBZ 功能描述:BOARD EVALUATION FOR AD9862 RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件,板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796
主站蜘蛛池模板: 乃东县| 南部县| 阿坝| 东兰县| 台中县| 桐乡市| 丰城市| 蕲春县| 景泰县| 嘉义市| 黄冈市| 铁岭县| 日土县| 普宁市| 洮南市| 武强县| 麦盖提县| 蕉岭县| 交城县| 镇康县| 新巴尔虎右旗| 安图县| 赤壁市| 乐山市| 伊春市| 陆河县| 新蔡县| 仁布县| 满城县| 松原市| 南涧| 肇源县| 耒阳市| 大渡口区| 息烽县| 绿春县| 乌拉特后旗| 万安县| 广德县| 高雄县| 通州市|