- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9882KST-140 (ANALOG DEVICES INC) Dual Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9882KST-140 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | Dual Interface for Flat Panel Displays |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封裝： | PLASTIC, MS-026BED, LQFP-100 |
| 文件頁數： | 35/36頁 |
| 文件大小： | 370K |
| 代理商： | AD9882KST-140 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁
REV. A
AD9882
–35–
Some graphic controllers use levels of power when active (during
active picture time) that are substantially different from those used
when they are idle (during horizontal and vertical sync periods).
This can result in a measurable change in the voltage supplied to
the analog supply regulator, which can in turn produce changes
in the regulated analog supply voltage. This can be mitigated by
regulating the analog supply, or at least PV
D
, from a different,
cleaner, power source (for example, from a 12 V supply).
Using a single ground plane for the entire board is also rec-
ommended. Experience has repeatedly shown that the noise
performance is the same or better with a single ground plane.
Using multiple ground planes can be detrimental because each
separate ground plane is smaller than one common ground
plane, and long ground loops can result.
In some cases, using separate ground planes is unavoidable. For
those cases where they must be used, it is recommended that at
least a single ground plane be placed under the AD9882. The loca-
tion of the split should be at the receiver of the digital outputs. For
this case, it is even more important to place components wisely
because the current loops will be much longer (current takes the
path of least resistance). The following is an example of a current
loop: power plane
AD9882
digital output trace
digital
data receiver
digital ground plane
analog ground plane.
PLL
Place the PLL loop filter components as close to the FILT pin
as possible.
Do not place any digital or other high frequency traces near
these components.
Use the values suggested in the data sheet with 10% or smaller
tolerances.
Outputs (Data and Clocks)
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance and require more
current, which causes more internal digital noise.
Shorter traces reduce the possibility of reflections.
Adding a series resistor with a value of 22
W
to 100
W
can suppress
reflections, reduce EMI, and reduce the current spikes inside of
the AD9882. However, if 50
W
traces are used on the PCB, the
data output should not need these resistors.
A 22
W
resistor on the DATACK output should provide good
impedance matching that will reduce reflections. If EMI or
current spiking is a concern, use a lower drive strength setting
by adjusting register 14H. If series resistors are used, place them as
close to the AD9882 pins as possible (but avoid adding vias or
extra length to the output trace in order to get the resistors closer).
If possible, limit the capacitance that each of the digital outputs
drives to less than 10 pF. This can be accomplished easily by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance will
increase the current transients inside the AD9882, creating
more digital noise on its power supplies.
Digital Inputs
The digital inputs on the AD9882 were designed to work
with 3.3 V signals, but are tolerant of 5.0 V signals. No extra
components need to be added if 5.0 V logic is used.
Any noise that gets onto the Hsync input trace will add jitter to
the system. Therefore, minimize the trace length and do not
run any digital or other high frequency traces near it.
Voltage Reference
Bypass with a 0.1
m
F capacitor. Place as close to the AD9882
pin as possible. Make the ground connection as short as possible.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9882 | Dual Interface for Flat Panel Displays |
| AD9883ABST-RL140 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883AKST-110 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883AKST-140 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883A | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9882KSTZ-100 | 功能描述:IC INTERFACE/DVI 100MHZ 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9882KSTZ-140 | 功能描述:IC INTERFACE/DVI 100MHZ 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9883 | 制造商:AD 制造商全稱:Analog Devices 功能描述:110 MSPS Analog Interface for Flat Panel Displays |
| AD9883/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:110 MSPS Analog Interface for Flat Panel Displays |
| AD9883A | 制造商:AD 制造商全稱:Analog Devices 功能描述:110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
發布緊急采購，3分鐘左右您將得到回復。