- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9883AKST-140 (ANALOG DEVICES INC) 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9883AKST-140 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| 封裝： | PLASTIC, MS-026BEC, LQFP-80 |
| 文件頁數： | 17/28頁 |
| 文件大小： | 229K |
| 代理商： | AD9883AKST-140 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. B
AD9883A
–17–
2-WIRE SERIAL CONTROL REGISTER DETAIL CHIP
IDENTIFICATION
00
7–0
Chip Revision
An 8-bit register that represents the silicon revision. Revi-
sion 0 = 0000 0000, Revision 1 = 0000 0001, Revision 2 =
0000 0010.
PLL DIVIDER CONTROL
01
7–0
PLL Divide Ratio MSBs
The 8 most significant bits of the 12-bit PLL divide ratio
PLLDIV. (The operational divide ratio is PLLDIV + 1.)
The PLL derives a master clock from an incoming Hsync
signal. The master clock frequency is then divided by an
integer value, such that the output is phase-locked to
Hsync. This PLLDIV value determines the number of
pixel times (pixels plus horizontal blanking overhead) per
line. This is typically 20% to 30% more than the number
of active pixels in the display.
The 12-bit value of the PLL divider supports divide ratios
from 2 to 4095. The higher the value loaded in this regis-
ter, the higher the resulting clock frequency with respect
to a fixed Hsync frequency.
VESA has established some standard timing specifications
that assist in determining the value for PLLDIV as a
function of horizontal and vertical display resolution and
frame rate (Table V).
However, many computer systems do not conform pre-
cisely to the recommendations, and these numbers should
be used only as a guide. The display system manufacturer
should provide automatic or manual means for optimizing
PLLDIV. An incorrectly set PLLDIV will usually produce
one or more vertical noise bars on the display. The greater
the error, the greater the number of bars produced.
The power-up default value of PLLDIV is 1693
(PLLDIVM = 69H, PLLDIVL = DxH).
The AD9883A updates the full divide ratio only when the
LSBs are changed. Writing to the MSB by itself will not
trigger an update.
02
7–4
PLL Divide Ratio LSBs
The 4 least significant bits of the 12-bit PLL divide ratio
PLLDIV. The operational divide ratio is PLLDIV + 1.
The power-up default value of PLLDIV is 1693
(PLLDIVM = 69H, PLLDIVL = DxH).
The AD9883A updates the full divide ratio only when this
register is written to.
CLOCK GENERATOR CONTROL
03
7–6
VCO Range Select
Two bits that establish the operating range of the clock
generator.
VCORNGE must be set to correspond with the desired
operating frequency (incoming pixel rate).
The PLL gives the best jitter performance at high fre-
quencies. For this reason, to output low pixel rates and
still get good jitter performance, the PLL actually operates
at a higher frequency but then divides down the clock rate
afterwards. Table VII shows the pixel rates for each VCO
range setting. The PLL output divisor is automatically
selected with the VCO range setting.
Table VII. VCO Ranges
VCORNGE
Pixel Rate Range
00
01
10
11
12–32
32–64
64–110
110–140
The power-up default value is 01.
5–3
CURRENT Charge Pump Current
Three bits that establish the current driving the loop filter
in the clock generator.
03
Table VIII. Charge Pump Currents
CURRENT
Current ( A)
000
001
010
011
100
101
110
111
50
100
150
250
350
500
750
1500
CURRENT must be set to correspond with the desired
operating frequency (incoming pixel rate).
The power-up default value is current = 001.
Table VI. Control Register Map (continued)
Write and
Read or
Read Only
Hex
Address
Default
Value
Register
Name
Bits
Function
16H
R/
W
7:0
Test Register
Reserved for future use.
17H
RO
7:0
Test Register
Reserved for future use.
18H
RO
7:0
Test Register
Reserved for future use.
*
The AD9883A only updates the PLL divide ratio when the LSBs are written to (register 02H).
相關PDF資料 |
PDF描述 |
|---|---|
| AD9883A | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883ABST-RL110 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883ABST-110 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883ABST-140 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883AKSTZ-110 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9883AKSTZ-110 | 功能描述:IC FLAT PANEL INTERFACE 80-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9883AKSTZ-110 | 制造商:Analog Devices 功能描述:IC ANALOG INTERFACE |
| AD9883AKSTZ-140 | 功能描述:IC FLAT PANEL INTERFACE 80-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9883AKSTZ-RL110 | 功能描述:IC INTERFACE FLAT 110MHZ 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| AD9883KST-110 | 制造商:Rochester Electronics LLC 功能描述:110MHZ ANALOG INTERFACE F - Bulk |
發布緊急采購，3分鐘左右您將得到回復。