- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9883AKSTZ-140 (ANALOG DEVICES INC) 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9883AKSTZ-140 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| 封裝： | PLASTIC, MS-026BEC, LQFP-80 |
| 文件頁數： | 22/28頁 |
| 文件大?。?/td> | 229K |
| 代理商： | AD9883AKSTZ-140 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. B
AD9883A
–22–
Table XXXIV. Detected Coast Input Polarity Status
Polarity Status
Result
0
1
Coast Polarity Negative
Coast Polarity Positive
This indicates that Bit 1 of Register 5 is the 4:2:2 Output
mode select bit.
1
4:2:2 Output Mode Select
A bit that configures the output data in 4:2:2 mode.
This mode can be used to reduce the number of data
lines used from 24 down to 16 for applications using
YUV, YCbCr, or YPbPr graphics signals. A timing
diagram for this mode is shown in Figure 9.
Recommended input and output configurations are
shown in Table XXXV.
15
Table XXXV. 4:2:2 Output Mode Select
Select
Output Mode
0
1
4:2:2
4:4:4
Table XXXVI. 4:2:2 Input/Output Configuration
Input
Connection
Channel
Output Format
Red
Green
Blue
V
Y
U
U/V
Y
High Impedance
2-WIRE SERIAL CONTROL PORT
A 2-wire serial interface control interface is provided. Up to two
AD9883A devices may be connected to the 2-wire serial interface,
with each device having a unique address.
The 2-wire serial interface comprises a clock (SCL) and a bidi-
rectional data (SDA) pin. The analog flat panel interface acts as
a slave for receiving and transmitting data over the serial interface.
When the serial interface is not active, the logic levels on SCL
and SDA are pulled high by external pull-up resistors.
Data received or transmitted on the SDA line must be stable for
the duration of the positive-going SCL pulse. Data on SDA must
change only when SCL is low. If SDA changes state while SCL
is high, the serial interface interprets that action as a start or
stop sequence.
There are five components to serial bus operation:
Start Signal
Slave Address Byte
Base Register Address Byte
Data Byte to Read or Write
Stop Signal
When the serial interface is inactive (SCL and SDA are high)
communications are initiated by sending a start signal. The start
signal is a high-to-low transition on SDA while SCL is high.
This signal alerts all slaved devices that a data transfer sequence
is coming.
The first eight bits of data transferred after a start signal com-
prise a 7-bit slave address (the first seven bits) and a single R/
W
Bit (the eighth bit). The R/
W
Bit indicates the direction of data
transfer, read from (1) or write to (0) the slave device. If the
transmitted slave address matches the address of the device (set by
the state of the SA
1-0
input pins in Table XXXIV, the AD9883A
acknowledges by bringing SDA low on the ninth SCL pulse. If the
addresses do not match, the AD9883A does not acknowledge.
Table XXXVII. Serial Port Addresses
Bit 7
A
6
(MSB)
Bit 6
A
5
Bit 5
A
4
Bit 4
A
3
Bit 3
A
2
Bit 2
A
1
Bit 1
A
0
1
1
0
0
0
0
1
1
1
1
0
0
0
1
Data Transfer via Serial Interface
For each byte of data read or written, the MSB is the first bit of
the sequence.
If the AD9883A does not acknowledge the master device during
a write sequence, the SDA remains high so the master can gen-
erate a stop signal. If the master device does not acknowledge the
AD9883A during a read sequence, the AD9883A interprets this
as “end of data.” The SDA remains high so the master can
generate a stop signal.
Writing data to specific control registers of the AD9883A requires
that the 8-bit address of the control register of interest be written
after the slave address has been established. This control register
address is the base address for subsequent write operations. The
base address autoincrements by one for each byte of data written
after the data byte intended for the base address. If more bytes
are transferred than there are available addresses, the address will
not increment and remains at its maximum value of 14H. Any base
address higher than 14H will not produce an acknowledge signal.
SDA
SCL
t
BUFF
t
STAH
t
DHO
t
DSU
t
DAL
t
DAH
t
STASU
t
STOSU
Figure 10. Serial Port Read/Write Timing
相關PDF資料 |
PDF描述 |
|---|---|
| AD9883KST-110 | 110 MSPS Analog Interface for Flat Panel Displays |
| AD9883 | 110 MSPS Analog Interface for Flat Panel Displays |
| AD9886 | Analog Interface for Flat Panel Displays |
| AD9886KS-100 | Analog Interface for Flat Panel Displays |
| AD9886KS-140 | Analog Interface for Flat Panel Displays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9883AKSTZ-RL110 | 功能描述:IC INTERFACE FLAT 110MHZ 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| AD9883KST-110 | 制造商:Rochester Electronics LLC 功能描述:110MHZ ANALOG INTERFACE F - Bulk |
| AD9884 | 制造商:AD 制造商全稱:Analog Devices 功能描述:100 MSPS/140 MSPS Analog Flat Panel Interface |
| AD9884A | 制造商:AD 制造商全稱:Analog Devices 功能描述:100 MSPS/140 MSPS Analog Flat Panel Interface |
| AD9884A/PCB | 制造商:Analog Devices 功能描述:140 MSPS GRAPHICS DIGITIZER |
發布緊急采購，3分鐘左右您將得到回復。