- 您現在的位置：買賣IC網 > PDF目錄373977 > ADCMP580_05 (Analog Devices, Inc.) Ultrafast SiGe Voltage Comparators PDF資料下載
參數資料
| 型號： | ADCMP580_05 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Ultrafast SiGe Voltage Comparators |
| 中文描述： | 超高速電壓比較器硅鍺 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 284K |
| 代理商： | ADCMP580_05 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
ADCMP580/ADCMP581/ADCMP582
COMPARATOR HYSTERESIS
Adding hysteresis to a comparator is often desirable in a noisy
environment or when the differential inputs are very small or
slow moving. The transfer function for a comparator with
hysteresis is shown in Figure 28. If the input voltage approaches
the threshold from the negative direction, the comparator
switches from a low to a high when the input crosses +V
H
/2.
The new switching threshold becomes V
H
/2. The comparator
remains in the high state until the threshold V
H
/2 is crossed
from the positive direction. In this manner, noise centered on
0 V input does not cause the comparator to switch states unless
it exceeds the region bounded by ±V
H
/2.
Rev. 0 | Page 13 of 16
The customary technique for introducing hysteresis into a
comparator uses positive feedback from the output back to
the input. A limitation of this approach is that the amount
of hysteresis varies with the output logic levels, resulting in
hysteresis that is not symmetric about the threshold. The
external feedback network can also introduce significant
parasitics that reduce high speed performance and can even
reduce overall stability in some cases.
OUTPUT
INPUT
0V
0
1
+V
H
2
–V
H
2
0
Figure 28. Comparator Hysteresis Transfer Function
The ADCMP58x family of comparators offers a programmable
hysteresis feature that can significantly improve the accuracy
and stability of the desired hysteresis. By connecting an external
pull-down resistor from the HYS pin to V
EE
, a variable amount
of hysteresis can be applied. Leaving the HYS pin disconnected
disables the feature, and hysteresis is then less than 1 mV, as
specified. The maximum range of hysteresis that can be applied
by using this method is approximately ±25 mV.
Figure 29 illustrates the amount of applied hysteresis as a
function of external resistor value. The advantage of applying
hysteresis in this manner is improved accuracy, stability, and
reduced component count. An external bypass capacitor is not
required on the HYS pin and it would likely degrade the jitter
performance of the device.
The hysteresis pin may also be driven by a current source.
It is biased approximately 400 mV above V
EE
and has an
internal series resistance of approximately 600 Ω.
80
0
0
10k
0
RESISTOR (
Ω
)
H
70
60
50
40
30
20
10
10
100
1k
Figure 29. Comparator Hysteresis vs. R
HYS
Control Resistor
MINIMUM INPUT SLEW RATE REQUIREMENT
As with many high speed comparators, a minimum slew rate
requirement must be met to ensure that the device does not
oscillate as the input signal crosses the threshold. This oscil-
lation is due in part to the high input bandwidth of the comparator
and the feedback parasitics inherent in the package. A
minimum slew rate of 50 V/μs should ensure clean output
transitions from the ADCMP58x family of comparators.
The slew rate may be too slow for other reasons. The extremely
high bandwidth of these devices means that broadband noise
can be a significant factor when input slew rates are low. There
is 120 μV of thermal noise generated over the comparator’s
bandwidth by the two 50 Ω terminations at room temperature.
With a slew rate of only 50 V/μs, the inputs will be inside this
noise band for over 2 ps, rendering the comparator’s jitter
performance of 200 fs irrelevant. Raising the slew rate of the
input signal and/or reducing the bandwidth over which that
resistance is seen at the input can greatly reduce jitter. We do
not characterize the devices this way, but simply bypassing a
reference input close to the package can reduce jitter 30% in
low slew rate applications.
相關PDF資料 |
PDF描述 |
|---|---|
| ADCMP580BCP-R2 | Ultrafast SiGe Voltage Comparators |
| ADCMP580BCP-RL7 | Ultrafast SiGe Voltage Comparators |
| ADCMP580BCP-WP | Ultrafast SiGe Voltage Comparators |
| ADCMP581 | Ultrafast SiGe Voltage Comparators |
| ADCMP581BCP-R2 | Ultrafast SiGe Voltage Comparators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADCMP580BCP | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultrafast SiGe Voltage Comparator |
| ADCMP580BCP-R2 | 制造商:Analog Devices 功能描述:Comparator Single ±5.5V 16-Pin LFCSP EP T/R |
| ADCMP580BCP-RL7 | 制造商:Analog Devices 功能描述:Comparator Single ±5.5V 16-Pin LFCSP EP T/R |
| ADCMP580BCP-WP | 制造商:Analog Devices 功能描述:Comparator Single ±5.5V 16-Pin LFCSP EP 制造商:Analog Devices 功能描述:IC ((NS)) |
| ADCMP580BCPZ-R2 | 功能描述:IC COMPARATOR CML UFAST 16-LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
發布緊急采購，3分鐘左右您將得到回復。