- 您現在的位置：買賣IC網 > PDF目錄373980 > ADE7753ARS (ANALOG DEVICES INC) Active and Apparent Energy Metering IC with di/dt sensor interface PDF資料下載
參數資料
| 型號： | ADE7753ARS |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Active and Apparent Energy Metering IC with di/dt sensor interface |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | MO-150AE, SSOP-20 |
| 文件頁數： | 6/38頁 |
| 文件大小： | 449K |
| 代理商： | ADE7753ARS |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
ADE7753
–6–
REV. PrF 10/02
PRELIMINARY TECHNICAL DATA
PIN F UNC T ION D E SC RIPT ION
Pin No.
M NE M O NIC
D E SC R IP T ION
1
RESET
Reset pin for the ADE7753. A logic low on this pin will hold the ADCs and digital
circuitry (including the Serial Interface) in a reset condition.
Digital power supply. T his pin provides the supply voltage for the digital circuitry in
the ADE7753. T he supply voltage should be maintained at 5V ± 5% for specified op-
eration. T his pin should be decoupled to DGND with a 10μF capacitor in parallel with
a ceramic 100nF capacitor.
Analog power supply. T his pin provides the supply voltage for the analog circuitry in
the ADE7753. T he supply should be maintained at 5V ± 5% for specified operation.
Every effort should be made to minimize power supply ripple and noise at this pin by
the use of proper decoupling. T he typical performance graphs in this data sheet show
the power supply rejection performance. T his pin should be decoupled to AGND with a
10μF capacitor in parallel with a ceramic 100nF capacitor.
Analog inputs for Channel 1. T his channel is intended for use with the di/dt current
transducer such as Rogowski coil or other current sensor such as shunt or current trans-
former (CT ). T hese inputs are fully differential voltage inputs with maximum
differential input signal levels of ±0.5V, ±0.25V and ±0.125V, depending on the full
scale selection - See
Analog Inputs
. Channel 1 also has a PGA with gain selections of 1,
2, 4, 8 or 16. T he maximum signal level at these pins with respect to AGND is ±0.5V.
Both inputs have internal ESD protection circuitry and in addition an overvoltage of
±6V can be sustained on these inputs without risk of permanent damage.
Analog inputs for Channel 2. T his channel is intended for use with the voltage trans-
ducer. T hese inputs are fully differential voltage inputs with a maximum differential
signal level of ±0.5V. Channel 2 also has a PGA with gain selections of 1, 2, 4, 8 or
16. T he maximum signal level at these pins with respect to AGND is ±0.5V. Both
inputs have internal ESD protection circuitry, and an overvoltage of ±6V can be sus-
tained on these inputs without risk of permanent damage.
T his pin provides the ground reference for the analog circuitry in the ADE7753, i.e.
ADCs and reference. T his pin should be tied to the analog ground plane or the quietest
ground reference in the system. T his quiet ground reference should be used for all ana-
log circuitry, e.g. anti-aliasing filters, current and voltage transducers etc. In order to
keep ground noise around the ADE7753 to a minimum, the quiet ground plane should
only connected to the digital ground plane at one point. It is acceptable to place the
entire device on the analog ground plane - see
Applications Information
.
T his pin provides access to the on-chip voltage reference. T he on-chip reference has a
nominal value of 2.4V ± 8% and a typical temperature coefficient of 20ppm/°C. An
external reference source may also be connected at this pin. In either case this pin
should be decoupled to AGND with a 1μF ceramic capacitor.
T his provides the ground reference for the digital circuitry in the ADE7753, i.e. multi-
plier, filters and digital-to-frequency converter. Because the digital return currents in
the ADE7753 are small, it is acceptable to connect this pin to the analog ground plane
of the system - see
Applications Information
. However, high bus capacitance on the DOUT
pin may result in noisy digital current which could affect performance.
Calibration Frequency logic output. T he CF logic output gives Active Power informa-
tion. T his output is intended to be used for operational and calibration purposes. T he
full-scale output frequency can be adjusted by writing to the CFDEN and CFNUM
Register—see
Energy To Frequency Conversion.
Voltage waveform (Channel 2) zero crossing output. T his output toggles logic high and
low at the zero crossing of the differential signal on Channel 2—see
Zero Crossing Detection
.
T his open drain logic output goes active low when either no zero crossings are detected
or a low voltage threshold (Channel 2) is crossed for a specified duration. See
Line Volt-
age Sag Detection.
Interrupt Request Output. T his is an active low open drain logic output. Maskable
interrupts include: Active Energy Register roll-over, Active Energy Register at half
level, and arrivals of new waveform samples. See
ADE7753 Interrupts
.
2
DV
DD
3
AV
DD
4,5
V1P, V1N
6,7
V2N, V2P
8
A G N D
9
REF
IN/OUT
10
D G N D
11
C F
12
Z X
13
SAG
14
IRQ
相關PDF資料 |
PDF描述 |
|---|---|
| ADE7753ARSRL | Active and Apparent Energy Metering IC with di/dt sensor interface |
| ADE7754 | ADE7754 |
| ADE7754AR | ADE7754 |
| ADE7754ARRL | ADE7754 |
| ADE7755AN-REF | Energy Metering IC with Pulse Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADE7753ARSRL | 制造商:Analog Devices 功能描述:Single Phase Multifunction Metering IC 20-Pin SSOP T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADE7753ARSZ | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7753ARSZ | 制造商:Analog Devices 功能描述:ENERGY METERING IC |
| ADE7753ARSZ | 制造商:Analog Devices 功能描述:IC MULTIFUNCTION METER |
| ADE7753ARSZRL | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
發布緊急采購，3分鐘左右您將得到回復。