- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1026JST-REEL (ANALOG DEVICES INC) Complete Thermal and System Management Controller PDF資料下載
參數資料
| 型號： | ADM1026JST-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Complete Thermal and System Management Controller |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 31/56頁 |
| 文件大小： | 634K |
| 代理商： | ADM1026JST-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ADM1026
Note that the THERM pin is bidirectional, so THERM may be
pulled low externally as an input. This causes the PWM and
DAC outputs to go to full scale until THERM is returned high
again. To disable THERM as an input, set Bit 0 of Configuration
Register 3 (Reg. 07h). This configures Pin 42 as GPIO16 and
prevents a low on Pin 42 from driving the fans at full speed.
Rev. A | Page 31 of 56
THERM LIMIT
THERM LIMIT – 5°C
THERM
INT
INT CLEARED BY STATUS REG 1 READ,
BIT 2 OF CONFIG. REG. 1 SET, OR ARA
TEMPERATURE
0
Figure 54. Assertion of INT Due to THERM Event
Reset Input and Outputs
The ADM1026 has two active low, power-on reset outputs,
RESETMAIN and RESETSTBY. These operate as follows.
RESETSTBY monitors 3.3 V STBY. At power-up, RESETSTBY is
asserted (pulled low) until 180 ms after 3.3 V STBY rises above
the reset threshold.
RESETMAIN monitors 3.3 V MAIN. This means that at power-
up, RESETMAIN is asserted (pulled low) until 180 ms after
3.3 V MAIN rises above the reset threshold.
If 3.3 V MAIN rises with or before DV
CC
, RESETMAIN
remains asserted until 180 ms after RESETSTBY is negated.
RESETMAIN can also function as a RESET input. Pulling this
pin low resets the registers, which are initialized to their default
values by a software reset. (See the Software Reset Function
section for register details).
Note that the 3.3 V STBY pin supplies power to the ADM1026.
In applications that do not require monitoring of a 3.3 V STBY
and 3.3 V MAIN supply, these two pins should be connected
together (3.3 V MAIN should not be left floating).
To ensure that the 3.3 V STBY pin does not become backdriven,
the 3.3 V STBY supply should power on before all other voltages
in the system.
See Table 3 for more information about pin configuration.
RESETSTBY
RESETMAIN
3.3VMAIN
~1V
180ms
POWER-ON RESET
180ms
3.3VSTBY
~1V
0
Figure 55. Operation of Offset Outputs
NAND TREE TESTS
A NAND tree is provided in the ADM1026 for automated test
equipment (ATE) board-level connectivity testing. This allows
the functionality of all digital inputs to be tested in a simple
manner and any pins that are nonfunctional or shorted together
to be identified. The structure of the NAND tree is shown in
Figure 56. The device is placed into NAND tree test mode by
powering up with Pin 25 held high. This pin is sampled
automatically after power-up, and if it is connected high, then
the NAND test mode is invoked.
NTESTOUT
GPIO8
FAN0
FAN1
FAN2
FAN3
FAN4
FAN5
FAN6
CI
SDA
SCL
FAN7
INT
GPIO9
GPIO10
GPIO11
GPIO12
GPIO13
GPIO14
GPIO15
GPIO16
0
Figure 56. NAND Tree
The NAND tree test may be carried out in one of two ways.
1.
Start with all inputs low and take them high in turn,
starting with the input nearest to NTEST_OUT
(GPIO16/THERM) and working back up the tree to the
input furthest from NTESTOUT (INT). This should give
the characteristic output pattern shown in Figure 57, with
NTESTOUT toggling each time an input is taken high.
2.
Start with all inputs high and take them low in turn,
starting with the input furthest from NTEST_OUT (INT)
and working down the tree to the input nearest to
NTEST_OUT (GPIO16/ THERM). This should give a
similar output pattern to Figure 58.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1026JSTZ-REEL | Complete Thermal and System Management Controller |
| ADM1026JST | Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 |
| ADM1030ARQ | Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
| ADM1033 | Thermal Monitor and Fan Speed (RPM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-R7 | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-REEL | 功能描述:板上安裝溫度傳感器 HI INT SYS MONITR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1026JSTZ-REEL7 | 制造商:Analog Devices 功能描述:IC SYSTEM MONITOR 制造商:ON Semiconductor 功能描述:IC SYSTEM MONITOR |
發布緊急采購，3分鐘左右您將得到回復。