- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADM1029ARQZ-R7 (ON Semiconductor)IC SENSOR 2TEMP/FAN CTRL 24QSOP Datasheet資料下載
參數資料
| 型號： | ADM1029ARQZ-R7 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 14/50頁 |
| 文件大小： | 402K |
| 描述： | IC SENSOR 2TEMP/FAN CTRL 24QSOP |
| 產品變化通告： | QSOP 24ld Pkg (MSL) Change 17/Jun/2010 |
| 標準包裝： | 1,000 |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 100°C，外部傳感器 |
| 精確度： | ±1°C 本地，±3°C 遠程 |
| 拓撲： | ADC，風扇控制，寄存器庫 |
| 輸出類型： | 開路漏極 |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 100°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
ADM1029
http://onsemi.com
14
If two fans are installed, Bit 0 would be 1 by default and
Pin 18 would be tied high* to set Bit 1. If only one fan is
installed, it would normally be Fan 1 and Pin 18 would be
tied low* to clear Bit 1. However, both of these bits can be
modified by writing to the register, so it is possible to have
Fan 2 installed and not Fan 1, or even have no fans installed.
* Note that Pin 18 also sets TMIN for automatic fan speed control. If
this function is used, Pin 18 would be set to some other level
according to Table 13.
FAULT
Inputs/Outputs
The ADM1029 can be used with fans that have a fault
output which indicates if the fan has stalled or failed. If one
or both of the FAULT
inputs (Pin 2 or Pin 23) goes low, both
INT
and CFAULT
will be asserted.
Events on the fault inputs are also reflected in Bits 2 and
3 of the corresponding Fan Status Registers at addresses 10h
and 11h. Bit 2 reflects the inverse state of the FAULT
pin (0
if FAULT
is high, 1 if FAULT
is low), while Bit 3 is latched
high if a FAULT
input goes low. It must be cleared by writing
a zero to it.
If the fan(s) being used do not have a FAULT
output, the
FAULT
input(s) on the ADM1029 should be pulled high to
V
CC
.
The FAULT
pins can also be configured as open-drain
outputs by setting Bit 5 of the corresponding Fan Fault
Action Register (18h or 19h). If a FAULT
pin is configured
as an output, it will still function as an input. This means that
when a fault input occurs it will be latched low by the fault
output, even if the fault input is removed. The fault output
can be used to drive a fan failure indicator such as an LED.
If the FAULT
pin is used as an output, any input to the
FAULT
pin should also be open-drain. This will avoid the
fault input trying to source a high current into the FAULT
pin
if the fault input goes high while the fault output is low.
Fan Present Inputs
The fan PRESENT
signal is implemented by a shorting
link to ground in the fan connector. When the fan is plugged
in, the corresponding PRESENT
input (Pin 4 or Pin 21) on
the ADM1029 is pulled low. If the fan is unplugged, the
PRESENT
input will be pulled high. INT
and CFAULT
will
be asserted (unless masked) and the event will be reflected
in Bits 0 and Bit 1 of the corresponding Fan Status Register.
Appearance or disappearance of a PRESENT
input signal
during normal operation signals to the ADM1029 that a fan
has been hot-plugged or unplugged. INT
and CFAULT
will
be asserted (unless masked). When a fan is hot-plugged,
Bit 7 of the corresponding Fan Status Register will be set
and a Fan Free Wheel Test commences automatically.
Fan Speed Measurement
The fan counter does not count the fan tach output pulses
directly, because at low fan speeds it would take several
seconds to accumulate a reasonably large and accurate
count. Instead, the period of the fan revolution is measured
by gating an onchip oscillator into the input of an 8-bit
counter.
The fan speed measuring circuit is initialized on the first
rising edge of a fan tach pulse after monitoring is enabled by
setting Bit 4 of the Configuration Register. It then starts
counting on the rising edge of the second tach pulse and
counts for four fan tach periods, until the rising edge of the
sixth tach pulse, or until the counter overranges if the fan
tach period is too long.
After the speed of the first fan has been measured, the
speed of the second fan (if installed) will be measured in the
same way. The measurement cycle will repeat until
monitoring is disabled. The fan speed measurements are
stored in the Fan Tach Value registers at addresses 70h and
71h.
If both fans are installed, Fan 1 will be measured first. If
only one fan is installed, the ADM1029 will still try to
measure both fans, starting with Fan 1, but the measurement
on the noninstalled fan will time out when the Fan Tach
Value count overranges.
The fan speed count is given by:
(eq. 2)
Count + f 4 60RN
where:
f is oscillator frequency in Hz
factor 4 is because 4 tach periods are counted
factor 60 is to convert minutes to seconds
R = fan speed in RPM
N is number of tach pulses per revolution
The frequency of the oscillator can be adjusted to suit the
expected frequency range of the fan tach pulses, which
depends on the fan speed and the number of tach pulses
produced for each revolution of the fan, which is either 1, 2,
or 4. The oscillator frequency is set by Bits 7 and 6 of the Fan
Configuration Registers (68h for Fan 1 and 69h for Fan 2).
Table 8. OSCILLATOR FREQUENCIES
Bit 7
Bit 6
Oscillator Frequency (Hz)
0
0
Measurement Disabled
0
1
470
1
0
940
1
1
1880
Figure 24. Fan Speed Measurement
CLOCK
CONFIG
REG. BIT 4
FAN 1
TACH
FAN 1
MEASUREMENT
PERIOD
FAN 2
MEASUREMENT
PERIOD
START OF
MONITORING
CYCLE
FAN 2
TACH
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1030ARQZ-RL7 | IC SNSR TEMP/FAN PWM CTRL 16QSOP |
| ADM1032ARZ-REEL | IC TEMP MONITOR 85DEG 8SOIC |
| ADM1033ARQZ-RL7 | IC THERM/FAN SPEED CTLR 16-QSOP |
| ADM1034ARQZ-REEL | IC THERM/FAN SPEED CTRLR 16-QSOP |
| ADN8810ACPZ-REEL7 | IC CURRENT SOURCE(12BIT) 24LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1030 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030ARQ | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1030ARQ-REEL | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1030ARQ-REEL7 | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1030ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 TDM & PWM FAN CNTRLRS IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。