欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADM1030
廠商: Analog Devices, Inc.
元件分類: 圓形連接器
英文描述: Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35
中文描述: 智能溫度監視器和PWM風扇控制器
文件頁數: 21/28頁
文件大小: 278K
代理商: ADM1030
REV. 0
ADM1030
–21–
CH3 50.0mV
CH2 5.00mV
CH4 50.0mV
M 4.00ms A CH1 –2.00mV
CH1
1
4
T
T
Tek PreVu
: 250mV
@: –258mV
Figure 20. Fan Speed Sensing Waveform at TACH/AIN Pin
FAN SPEED MEASUREMENT
The fan counter does not count the fan tach output pulses
directly, because the fan speed may be less than 1000 RPM
and it would take several seconds to accumulate a reasonably
large and accurate count. Instead, the period of the fan revolu-
tion is measured by gating an on-chip 11.25 kHz oscillator into
the input of an 8-bit counter. The fan speed measuring circuit is
initialized on the rising edge of a PWM high output if fan speed
measurement is enabled (Bit 2 of Configuration Register 2 =
1). It then starts counting on the rising edge of the second tach
pulse and counts for two fan tach periods, until the rising edge of
the fourth tach pulse, or until the counter overranges if the fan
tach period is too long. The measurement cycle will repeat until
monitoring is disabled. The fan speed measurement is stored in
the Fan Speed Reading register at address 0x08.
The fan speed count is given by:
Count
= (
f
×
60)/
R
×
N
where:
f
=
11.25 kHz
R
=
Fan Speed in RPM.
N
=
Speed Range (Either 1, 2, 4, or 8)
The frequency of the oscillator can be adjusted to suit the expected
running speed of the fan by varying N, the Speed Range. The
oscillator frequency is set by Bits 7 and 6 of Fan Characteristics
Register 1 (20h) as shown in Table XI. Figure 21 shows how the
fan measurements relate to the PWM_OUT pulse trains.
Table XI. Oscillator Frequencies
Oscillator
Frequency (kHz)
Bit 7
Bit 6
N
0
0
1
1
0
1
0
1
1
2
4
8
11.25
5.625
2.812
1.406
CLOCK
CONFIG 2
REG. BIT 2
FAN
INPUT
FAN
MEASUREMENT
PERIOD
START OF
MONITORING
CYCLE
Figure 21. Fan Speed Measurement
In situations where different output drive circuits are used for
fan drive, it may be desirable to invert the PWM drive signal.
Setting Bit 3 of Configuration Register 1 (0x00) to 1, inverts the
PWM_OUT signal. This makes the PWM_OUT pin high for
100% duty cycle. Bit 3 of Configuration Register 1 should gen-
erally be set to 1, when using an n-MOS device to drive the fan.
If using a p-MOS device, Bit 3 of Configuration Register 1
should be cleared to 0.
FAN FAULTS
The
FAN_FAULT
output (Pin 8) is an active-low, open-drain
output used to signal fan failure to the system processor. Writing a
Logic 1 to Bit 4 of Configuration Register 1 (0x00) enables the
FAN_FAULT
output pin. The
FAN_FAULT
output is enabled
by default. The
FAN_FAULT
output asserts low only when
five consecutive interrupts are generated by the ADM1030 device
due to the fan running underspeed, or if the fan is completely
stalled. Note that the Fan Tach High Limit must be exceeded
by at least one before a
FAN_FAULT
can be generated. For
example, if we are only interested in getting a
FAN_FAULT
if
the fan stalls, then the fan speed value will be 0xFF for a failed
fan. Therefore, we should make the Fan Tach High Limit =
0xFE to allow
FAN_FAULT
to be asserted after five consecu-
tive fan tach failures.
Figure 22 shows the relationship between
INT
,
FAN_FAULT
,
and the PWM drive channel. The PWM_OUT channel is driv-
ing a fan at some PWM duty cycle, say 50%, and the fan’s tach
signal (or fan current for a 2-wire fan) is being monitored at the
TACH/AIN pin. Tach pulses are being generated by the fan,
during the high time of the PWM duty cycle train. The tach is
pulled high during the off time of the PWM train because the
fan is connected high-side to the n-MOS device.
Suppose the fan has already failed its fan speed measurement
twice previously. Looking at Figure 22, PWM_OUT is brought
high for two seconds, to restart the fan if it has stalled. Some-
time later a third tach failure occurs. This is evident by the tach
signal being low during the high time of the PWM pulse, causing
the Fan Speed Reading register to reach its maximum count of
255. Since the tach limit has been exceeded, an interrupt is
generated on the
INT
pin. The Fan Fault bit (Bit 1) of Inter-
rupt Status Register 1 (Register 0x02) will also be asserted.
Once the processor has acknowledged the
INT
by reading the
status register, the
INT
is cleared. PWM_OUT is then brought
high for another 2 seconds to restart the fan. Subsequent fan
failures cause
INT
to be reasserted and the PWM_OUT signal
is brought high for 2 seconds (fan spin-up default) each time to
restart the fan. Once the fifth tach failure occurs, the failure is
deemed to be catastrophic, and the
FAN_FAULT
pin is asserted
low. PWM_OUT is brought high to attempt to restart the fan.
相關PDF資料
PDF描述
ADM1033 Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQ Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQ-REEL Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQ-REEL7 Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQZ Thermal Monitor and Fan Speed (RPM) Controller
相關代理商/技術參數
參數描述
ADM1030ARQ 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1030ARQ-REEL 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1030ARQ-REEL7 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1030ARQZ 功能描述:馬達/運動/點火控制器和驅動器 TDM & PWM FAN CNTRLRS IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
ADM1030ARQZ-REEL 功能描述:板上安裝溫度傳感器 TDM PWM FAN CTRLRS IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
主站蜘蛛池模板: 楚雄市| 富阳市| 巴林左旗| 西昌市| 城口县| 永胜县| 金沙县| 茶陵县| 左云县| 万安县| 哈巴河县| 龙江县| 临夏市| 高要市| 宁河县| 阿坝县| 张家口市| 乃东县| 永平县| 浦北县| 肇东市| 平乐县| 靖远县| 准格尔旗| 崇信县| 威远县| 郑州市| 泗洪县| 阜平县| 长乐市| 特克斯县| 尚志市| 泾源县| 胶州市| 兴安盟| 禹州市| 鸡泽县| 丰城市| 象州县| 城口县| 仁布县|