- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADM1030ARQZ-RL7 (ON Semiconductor)IC SNSR TEMP/FAN PWM CTRL 16QSOP Datasheet資料下載
參數資料
| 型號： | ADM1030ARQZ-RL7 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 11/30頁 |
| 文件大小： | 327K |
| 描述： | IC SNSR TEMP/FAN PWM CTRL 16QSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi Product Obsolescence 11/Feb/2009 |
| 標準包裝： | 1,000 |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 100°C，外部傳感器 |
| 精確度： | ±1°C，±1°C（最小值） |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 100°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
ADM1030
http://onsemi.com
11
noisy environment, a capacitor of value up to 1000 pF may
be placed between the D+ and D inputs to filter the noise.
To measure DV
BE
, the sensor is switched between
operating currents of I and N ?I. The resulting waveform is
passed through a 65 kHz low-pass filter to remove noise,
then to a chopperstabilized amplifier that performs the
functions of amplification and rectification of the waveform
to produce a dc voltage proportional to DV
BE
. This voltage
is measured by the ADC to give a temperature output in
11-bit twos complement format. To further reduce the
effects of noise, digital filtering is performed by averaging
the results of 16 measurement cycles. An external
temperature measurement nominally takes 9.6 ms.
Layout Considerations
Digital boards can be electrically noisy environments and
care must be taken to protect the analog inputs from noise,
particularly when measuring the very small voltages from
a remote diode sensor. The following precautions should be
taken:
1. Place the ADM1030 as close as possible to the
remote sensing diode. Provided that the worst
noise sources such as clock generators,
data/address buses, and CRTs are avoided, this
distance can be 4 to 8 inches.
2. Route the D+ and D tracks close together, in
parallel, with grounded guard tracks on each side.
Provide a ground plane under the tracks if
possible.
3. Use wide tracks to minimize inductance and
reduce noise pick-up. 10 mil track minimum width
and spacing is recommended.
Figure 19. Arrangement of Signal Tracks
10 MIL
10 MIL
10 MIL
10 MIL
10 MIL
10 MIL
10 MIL
GND
D
D+
GND
4. Try to minimize the number of copper/solder
joints, which can cause thermocouple effects.
Where copper/solder joints are used, make sure
that they are in both the D+ and D path and at the
same temperature.
Thermocouple effects should not be a major
problem as 1癈 corresponds to about 200 mV, and
thermocouple voltages are about 3 mV/癈 of
temperature difference. Unless there are two
thermocouples with a big temperature differential
between them, thermocouple voltages should be
much less than 200 mV.
5. Place a 0.1 mF bypass capacitor close to the
ADM1030.
6. If the distance to the remote sensor is more than
8 inches, the use of twisted pair cable is
recommended. This will work up to about 6 to
12 feet.
7. For really long distances (up to 100 feet) use
shielded twisted pair such as Belden #8451
microphone cable. Connect the twisted pair to D+
and D and the shield to GND close to the
ADM1030. Leave the remote end of the shield
unconnected to avoid ground loops.
Because the measurement technique uses switched
current sources, excessive cable and/or filter capacitance
can affect the measurement. When using long cables, the
filter capacitor C1 may be reduced or removed. In any case
the total shunt capacitance should not exceed 1000 pF.
Cable resistance can also introduce errors. 1 W series
resistance introduces about 0.5癈 error.
Addressing the Device
ADD (Pin 13) is a three-state input. It is sampled, on
power-up to set the lowest two bits of the serial bus address.
Up to three addresses are available to the systems designer
via this address pin. This reduces the likelihood of conflicts
with other devices attached to the System Management Bus.
The ADM1030 Interrupt System
The ADM1030 has two interrupt outputs, INT
and
THERM
. These have different functions. INT
responds to
violations of software programmed temperature limits and
is maskable (described in more detail later).
THERM
is intended as a fail-safe interrupt output that
cannot be masked. If the temperature is below the low
temperature limit, the INT
pin will be asserted low to
indicate an out-of-limit condition. If the temperature
exceeds the high temperature limit, the INT
pin will also be
asserted low. A third limit; THERM
limit, may be
programmed into the device to set the temperature limit
above which the overtemperature THERM
pin will be
asserted low. The behavior of the high limit and THERM
limit is as follows:
1. Whenever the temperature measured exceeds the
high temperature limit, the INT
pin is asserted low.
2. If the temperature exceeds the THERM
limit, the
THERM
output asserts low. This can be used to
throttle the CPU clock. If the THERM
-to-Fan
Enable bit (Bit 7 of THERM
behavior/revision
register) is cleared to 0, the fan will not run
full-speed. The THERM
limit may be programmed
at a lower temperature than the high temperature
limit. This allows the system to run in silent mode,
where the CPU can be throttled while the cooling
fan is off. If the temperature continues to increase,
and exceeds the high temperature limit, an INT
is
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1032ARZ-REEL | IC TEMP MONITOR 85DEG 8SOIC |
| ADM1033ARQZ-RL7 | IC THERM/FAN SPEED CTLR 16-QSOP |
| ADM1034ARQZ-REEL | IC THERM/FAN SPEED CTRLR 16-QSOP |
| ADN8810ACPZ-REEL7 | IC CURRENT SOURCE(12BIT) 24LFCSP |
| ADP2140ACPZ3328R7 | IC REG DL BCK/LINEAR 10LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1031 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Intelligent Temperature Monitor and Dual PWM Fan Controller |
| ADM1031ARQ | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1031ARQ-ND | 制造商:ON Semiconductor 功能描述: |
| ADM1031ARQ-REEL | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1031ARQ-REEL7 | 功能描述:IC SENSOR 2-TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。