- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1033ARQ-REEL7 (ANALOG DEVICES INC) Thermal Monitor and Fan Speed (RPM) Controller PDF資料下載
參數資料
| 型號： | ADM1033ARQ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Thermal Monitor and Fan Speed (RPM) Controller |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | MO-137AB, QSOP-16 |
| 文件頁數： | 10/40頁 |
| 文件大小： | 1164K |
| 代理商： | ADM1033ARQ-REEL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADM1033
FUNCTIONAL DESCRIPTION
The ADM1033 is a local and remote temperature monitor
and fan controller used in a variety of applications, including
microprocessor-based systems. The device accurately monitors
remote and ambient temperature and uses that information to
quietly control the speed of a cooling fan. Whenever the fan
stalls, the device asserts a FAN_FAULT output.
Rev. 0 | Page 10 of 40
The ADM1033 has a THERM I/O. As an input, this measures
assertions on the THERM pin. As an output, it asserts a low
signal to indicate when the measured temperature exceeds the
programmed THERM temperature limits. The ADM1033
communicates over an SMBus 2.0 interface. Its LOCATION
input determines which version of SMBus to use, as well as the
SMBus address (in fixed-and-discoverable mode), and the
LOCATION bits in the UDID (in ARP-capable mode).
INTERNAL REGISTERS
Table 4 gives a brief description of the ADM1033’s principal
internal registers. For more detailed information on the
function of each register, refer to .
SERIAL BUS INTERFACE
The ADM1033 communicates with the master via the 2-wire
SMBus 2.0 interface. It supports two SMBus 2.0 versions,
determined by the value of the LOCATION input resistors.
The first version is fully ARP-capable. This means that it
supports address resolution protocol (ARP), allowing the
master to dynamically address the device on power-up. It
responds to ARP commands such as “Prepare to ARP.”
The second SMBus version, fixed-and-discoverable, is
backward-compatible with SMBus 1.0 and 1.1. In this mode, the
ADM1033 powers up with a fixed address, which is determined
by the state of the LOCATION pin on power-up. Note: when
using the ADM1033, addresses 0xC2 and 0xCA should not be
used by any other device on the bus.
LOCATION INPUT
The LOCATION input is a resistor divider input. It has multiple
functions and can specify the following: the SMBus version
(in fixed-and-discoverable or ARP-capable modes); the SMBus
address (in fixed-and-discoverable mode); and the LLL bits
(in UDID in ARP-capable mode).
The voltage of this 8-level input is set by a potential divider. The
voltage on LOCATION is sampled on power-up and digitized
by the on-chip ADC to determine the LOCATION input value.
Because the LOCATION input is sampled only at power-up,
changes made while power is applied have no effect.
V
CC
GND
ADM1033
R1
R2
LOCATION
PIN 13
0
Figure 16. Bootstrapping the LOCATION Input
SMBus 2.0 ARP-CAPABLE MODE
In ARP-capable mode, the ADM1033 supports such features as
address resolution protocol (ARP) and unique device identifier
(UDID). The UDID is a 128-bit message that describes the
ADM1033’s capabilities to the master. The UDID also includes a
vendor-specific ID for functionally equivalent devices.
V
CC
1.5k
1k
1k
1k
1k
1k
1.5k
GND
ADM1033 NO. 1
ADM1033 NO. 2
ADM1033 NO. 3
ADM1033 NO. 5
ADM1033 NO. 7
ARP
LOCATION = 111
ARP
LOCATION = 110
ADM1033 NO. 4
ARP
LOCATION = 101
ARP
LOCATION = 100
ADM1033 NO. 6
FD
ADDRESS = 53h
FD
ADDRESS = 52h
ADM1033 NO. 8
FD
ADDRESS = 51h
FD
ADDRESS = 50h
0
Figure 17. Setting Up Multiple ADM1033 Addresses
In SMBus 2.0 mode, this vendor-specific ID is generated by an
on-chip random number generator. This should enable two
adjacent ADM1033s in the same system to power-up with a
different vendor-specific ID, allowing the master to identify the
two separate ADM1033s and assign a different address to each.
The state of the LOCATION input on power-up is also reflected
in the UDID. This is useful when there are more than one
ADM1033 in the system, so the master knows which one it is
communicating with. The UDID values are listed in Table 6.
The SMBus 2.0 master issues both general and directed ARP
commands. A general command is directed at all ARP devices.
A directed command is targeted at a single device, once an
address has been established. The PEC byte must be used for
ARP commands (refer to Packet Error Checking (PEC)). The
ADM1033 responds to the following commands:
Prepare to ARP (general)
Reset device (general and directed)
Get UDID (general and directed)
Assign address (general)
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1033ARQZ | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQZ-REEL | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQZ-REEL7 | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1041ARQ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1033ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 +/- 1 C Digital 2-Wire RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1033ARQZ-REEL | 功能描述:板上安裝溫度傳感器 +/- 1 C Digital 2-Wire RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1033ARQZ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1033ARQZ-RL7 | 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Thermal Monitor and Fan Speed (RPM) Controller |
發布緊急采購，3分鐘左右您將得到回復。