- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1033ARQZ-REEL7 (ANALOG DEVICES INC) Thermal Monitor and Fan Speed (RPM) Controller PDF資料下載
參數資料
| 型號： | ADM1033ARQZ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Thermal Monitor and Fan Speed (RPM) Controller |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | LEAD FREE, MO-137AB, QSOP-16 |
| 文件頁數： | 21/40頁 |
| 文件大小： | 1164K |
| 代理商： | ADM1033ARQZ-REEL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADM1033
Table 16. Status Register 1 (Reg. 0x4F)
Bit No.
Name
7
LH
Rev. 0 | Page 21 of 40
Description
1 = Local high temperature limit has been
exceeded.
1 = Local low temperature limit has been
exceeded.
1= Remote high temperature limit has
been exceeded.
1 = Remote low temperature limit has
been exceeded.
1 = Remote diode error; indicates an
open or short on the D1+/D1 pins.
Reserved.
Reserved.
Reserved.
6
LL
5
RH
4
RL
3
RD
2
1
0
Unused
Unused
Unused
Table 17. Status Register 2 (Reg. 0x50)
Bit No.
Name
7
LT
Description
1 = Local THERM temperature limit has
been exceeded.
1 = Remote THERM temperature limit has
been exceeded.
Reserved.
1 = THERM timer limit has been
exceeded.
1 = One of the THERM limits has been
exceeded; and the THERM output signal
has been asserted.
1 = THERM pin is active. Clears on a read,
if THERM is not active.
Reserved.
Reserved.
6
RT
5
4
Unused
T%
3
TA
2
TS
1
0
Res
Res
Table 18. Status Register 3 (Reg. 0x51)
Bit No.
Name
7
FS
6
FA
Description
1= Fan has stalled.
1= Fan ALARM speed, indicates fan is
running at alarm speed.
Reserved.
Reserved.
Reserved.
Reserved.
Reserved.
1= SMBusALERT low, indicates the
ADM1033 has pulled the SMBusALERT
line low.
5
4
3
2
1
0
Res
Res
Res
Res
Res
ALERT
ALERT INTERRUPT BEHAVIOR
The ADM1033 generates an ALERT to signal out-of-limit
conditions. Out-of-limit conditions can also be detected by
polling the status registers. The ADM1033 has two ALERT
outputs, called ALERT Comp and SMBusALERT.
In SMBusALERT mode, the output remains low until the
following combination of conditions occur: the measurement
falls back within its programmed limits, and either the status
register is read or an ARA is completed.
In ALERT Comp mode, the output automatically resets
once the temperature measurement falls back within the
programmed limits.
For the SMBusALERT output, a status bit is set when a
measurement goes outside its programmed limit. If the
corresponding mask bit is not set, the SMBusALERT output
is pulled low. If the measured value falls back within the limits,
the SMBusALERT output remains low until the corresponding
status register is read or until an ARA is completed, as long as
no other measurement is outside its limits.
On the other hand, the ALERT Comp output is automatically
pulled low when a measurement goes outside its programmed
limits. Once the measurement falls back within its limits, the
ALERT output is automatically pulled back high again,
assuming no other measurement channel is outside its limits.
The main difference between the two outputs is that the
SMBusALERT does not reset without software intervention,
while the ALERT Comp output automatically resets itself. Note:
In this data sheet, an ALERT refers to both the ALERT Comp
and SMBusALERT, unless otherwise stated.
ALERT, 70
°
C
TEMPERATURE
LIMITS
TIME
CLEARED
ON READ
ALERT COMP
SMBusALERT
0
Figure 31. How ALERT Comparator and SMBusALERT Outputs Work
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1041ARQ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041A | Secondary-Side Controller with Current Share and Housekeeping |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1033ARQZ-RL7 | 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1034ARQ | 制造商:ON Semiconductor 功能描述:Temp Sensor Digital Serial (2-Wire) 16-Pin QSOP Tube 制造商:Rochester Electronics LLC 功能描述:DUAL FAN CONTROLLER, SRC, SMBUS I.C. - Bulk |
| ADM1034ARQ-REEL | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034ARQ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。