- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1033ARQZ-REEL7 (ANALOG DEVICES INC) Thermal Monitor and Fan Speed (RPM) Controller PDF資料下載
參數資料
| 型號： | ADM1033ARQZ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Thermal Monitor and Fan Speed (RPM) Controller |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | LEAD FREE, MO-137AB, QSOP-16 |
| 文件頁數： | 25/40頁 |
| 文件大小： | 1164K |
| 代理商： | ADM1033ARQZ-REEL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADM1033
FAN DRIVE SIGNAL
The ADM1033 controls the speed of a cooling fan. Varying the
duty cycle (on/off time) of a square wave applied to the fan
varies the speed of the fan. The ADM1033 uses a control
method called synchronous speed control, in which the PWM
drive signal applied to the fan is synchronized with the fan’s
TACH signal. See the Synchronous Speed Control section.
Rev. 0 | Page 25 of 40
The external circuitry required to drive the fan is simple. A
single N-channel MOSFET is the only drive device required.
The specifications of the MOSFET depend on the maximum
current required by the fan and the gate voltage drive (V
GS
< 3 V
for direct interfacing to the drive pin). V
GS
can be greater than
3 V, as long as the pull-up on the gate is tied to 5 V. The MOSFET
should also have a low on resistance to ensure that there is no
significant voltage drop across the FET. A high on resistance
reduces the voltage applied across the fan and, therefore, the
maximum operating speed of the fan. Figure 34 shows a scheme
for driving a 3-wire fan.
12V
12V
FAN
1N4148
Q1
NDT3055L
ADM1033
DRIVE
TACH
TACH
0
3.3V
100k
10k
10k
4.7k
12V
Figure 34. Interfacing a 3-Wire Fan to the ADM1033 Using an
N-Channel MOSFET
Figure 34 uses a 10 k pull-up resistor for the TACH signal.
This assumes that the TACH signal is an open collector from
the fan. In all cases, the fan’s TACH signal must be kept below 5
V maximum to prevent damaging the ADM1033.
If in doubt as to whether a fan has an open collector or totem-
pole TACH output, use one of the input signal conditioning
circuits shown in the Fan Inputs section.
When designing drive circuits with transistors and FETs, make
sure that the drive pins are not required to source current and
that they sink less than the maximum current specified.
SYNCHRONOUS SPEED CONTROL
The ADM1033 drives the fan using a control scheme called
synchronous speed control. In this scheme, the PWM drive
signal applied to the fan is synchronized with the TACH signal.
Accurate and repeatable fan speed measurements are the main
benefits. The fan is allowed to run reliably at speeds as low as
30 % of the full capability.
The drive signal applied to the fan is synchronized with the
TACH signal. The ADM1033 switches on the drive signal and
waits for a transition on the TACH signal. When a transition
takes place on the TACH signal, the PWM drive is switched off
for a period of time called t
OFF
. The drive signal is then switched
on again. The t
OFF
time is varied in order to vary the fan speed.
If the fan runs too fast, the t
OFF
time is increased. If the fan runs
too slow, the t
OFF
time is decreased.
Because the drive signal is synchronized with the TACH signal,
the frequency with which the fan is driven depends on the cur-
rent speed of the fan and the number of poles in it.
Figure 35 shows how the synchronous speed drive signal works.
The ideal
TACH
signal is the signal that would be output from
the fan, if power were applied 100% of the time. It is representa-
tive of the actual speed of the fan. The actual
TACH signal is the
signal seen on the TACH output from the fan, if using a scope.
In effect, the actual TACH signal is the ideal TACH signal
chopped with the drive signal.
IDEAL TACH
POLE TRANSITION POINTS
DASH = TACH FLOATS HIGH BY PULL-UP RESISTOR
SOLID = TRUE TACH WHEN FAN IS POWERED
DRIVE
ACTUAL TACH
t
OFF
t
POLE
0
Figure 35. Drive Signal by Using Synchronous Control
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1041ARQ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041A | Secondary-Side Controller with Current Share and Housekeeping |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1033ARQZ-RL7 | 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1034ARQ | 制造商:ON Semiconductor 功能描述:Temp Sensor Digital Serial (2-Wire) 16-Pin QSOP Tube 制造商:Rochester Electronics LLC 功能描述:DUAL FAN CONTROLLER, SRC, SMBUS I.C. - Bulk |
| ADM1034ARQ-REEL | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034ARQ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。