- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1033ARQZ-REEL (ANALOG DEVICES INC) Thermal Monitor and Fan Speed (RPM) Controller PDF資料下載
參數資料
| 型號： | ADM1033ARQZ-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Thermal Monitor and Fan Speed (RPM) Controller |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | LEAD FREE, MO-137AB, QSOP-16 |
| 文件頁數： | 14/40頁 |
| 文件大小： | 1164K |
| 代理商： | ADM1033ARQZ-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADM1033
REGISTER ADDRESSES FOR
SINGLE/BLOCK BYTE MODES
The ADM1033 supports single-byte and multiple-byte (block)
read and write operations. The register address determines
whether a single-byte or block operation is run. For a single-
byte operation, the MSB of the register address is set to 0; for a
multiple-byte operation, it is set to 1. The number of bytes read
from the ADM1033 in a multiple-byte operation is set in the
#Bytes/Block Read Register at Address 0x00. The number of
bytes written to it is specified in the block-write operation. The
addresses quoted in the register map and throughout this data
sheet assume single-byte operation. For multiple-byte opera-
tions, set the MSB of each register address to 1.
Rev. 0 | Page 14 of 40
The SMBus specifications define protocols for different types of
read and write operations. The ADM1033 supports the
following SMBus write protocols: send byte, write byte, block
write, receive byte, and block read. The following abbreviations
are used in the diagrams:
S—START
P—STOP
R—READ
W—WRITE
A—ACKNOWLEDGE
A—NO ACKNOWLEDGE
WRITE OPERATIONS
Send Byte
In this operation, the master device sends a single-command
byte to a slave device as follows:
1.
The master device asserts a start condition on SDA.
2.
The master sends a 7-bit address followed by the write bit
(low).
3.
The addressed slave device asserts ACK on SDA.
4.
The master sends the register address.
5.
The slave asserts ACK on SDA.
6.
The master asserts a stop condition on SDA, and the
transaction ends.
SLAVE
ADDRESS
S
REG
ADDRESS
W A
A P
0
Figure 21. Send Byte
The ADM1033 uses the send-byte operation to write a register
address to the APR for a subsequent read from the same
address. This is illustrated in Figure 21. The user may be
required to read data from the register immediately after setting
up the address. If so, the master can assert a repeat start
condition immediately after the final ACK and carry out a
single-byte read without asserting an intermediate stop condition.
Write Byte
In this operation, the master device sends the register address
and one data byte to the slave device as follows:
1.
2.
The master asserts a start condition on SDA.
The master sends the 7-bit slave address followed by a
write bit (low).
The addressed slave device asserts ACK on SDA.
The master sends the register address. The MSB of the
command code should equal 0 for a write-byte operation.
If the MSB equals 1, a block-write operation takes place.
The slave asserts ACK on SDA.
The master sends a data byte.
The slave asserts ACK on SDA.
The master asserts a stop condition on SDA to end the
transaction.
3.
4.
5.
6.
7.
8.
SLAVE
ADDRESS
S
REG
ADDRESS
DATA
W
A
A
A
P
0
Figure 22. Write Byte
Block Write
In this operation, the master device writes a block of data to a
slave address as follows. A maximum number of 32 bytes can
be written.
1.
The master asserts a start condition on SDA.
2.
The master sends the 7-bit slave address followed by a write
bit (low).
3.
The addressed slave device asserts ACK on SDA.
4.
The master sends the register address. This register address
sets up the address pointer register and determines if a
block write (MSB = 1) or a byte write (MSB = 0) takes place.
5.
The slave asserts ACK on SDA.
6.
The master sends the byte count.
7.
The slave asserts ACK on SDA.
8.
The master sends N data bytes.
9.
The slave asserts ACK on SDA after each byte.
10.
The master asserts a stop condition on SDA to end the
transaction.
SLAVE
ADDRESS
S
BYTE
COUNT
DATA 2
DATA 1
REGISTER
ADDRESS
W
A
A
P
A
A
A
DATA N
A
0
Figure 23. Block Write
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1033ARQZ-REEL7 | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1041ARQ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ | Secondary-Side Controller with Current Share and Housekeeping |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1033ARQZ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1033ARQZ-RL7 | 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1034ARQ | 制造商:ON Semiconductor 功能描述:Temp Sensor Digital Serial (2-Wire) 16-Pin QSOP Tube 制造商:Rochester Electronics LLC 功能描述:DUAL FAN CONTROLLER, SRC, SMBUS I.C. - Bulk |
| ADM1034ARQ-REEL | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。