- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1033ARQZ-REEL (ANALOG DEVICES INC) Thermal Monitor and Fan Speed (RPM) Controller PDF資料下載
參數資料
| 型號： | ADM1033ARQZ-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Thermal Monitor and Fan Speed (RPM) Controller |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | LEAD FREE, MO-137AB, QSOP-16 |
| 文件頁數： | 29/40頁 |
| 文件大?。?/td> | 1164K |
| 代理商： | ADM1033ARQZ-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADM1033
Rev. 0 | Page 29 of 40
FAN SPEED
T1
T2
T (3 TO 8) = 191
°
C
TEMPERATURE
TACH COUNT 2 TO 8
TACH COUNT 1
0
Figure 42. Programming Two Points on the Look-Up Table
Once the temperature exceeds the highest temperature point in
the look-up table, the fan speed remains at the highest speed
until the temperature drops below the T7 temperature value.
If the temperatures in T1 to T8 are not programmed in
succession, the fan speed moves to the next highest pro-
grammed temperature as the temperature increases. Similarly,
when the temperature decreases, it ignores programmed higher
temperatures and jumps to the next lower temperature. There-
fore, the temperature-to-fan-speed profile for increasing and
decreasing temperature can be different.
When programming the look-up table, the user has the option
to use between two and eight points for the fan (eight points
only if the same curve is to be used for both fans).
If the user wants to program only the transfer curve and knows
the starting temperature, minimum fan speed, maximum
temperature, and maximum fan speed, then only four parame-
ters are required: T1, T2, FS1, and FS2. The remaining look-up
temperature thresholds should remain at their default values of
+191°C. FS 3 to FS8 should be programmed with the same value
as FS2 to give the flat curve, if required, or, they can be left at
the default value of 0.
However, it is normal to program a THERM limit as well. Once
this temperature is exceeded and the boost bit is set, the fan
runs to full speed. This overrides the table.
Table 29. Look-Up Table Register Addresses
x
Temperature, x
RPMx, LSB
1
0x22
0x2A
2
0x23
0x2C
3
0x24
0x2E
4
0x25
0x30
5
0x26
0x32
6
0x27
0x34
7
0x28
0x36
8
0x29
0x38
RPMx, MSB
0x2B
0x2D
0x2F
0x31
0x33
0x35
0x37
0x39
SETTING UP THE LOOK-UP TABLE
IN LINEAR MODE
When discrete/linear speed (Bit 2) is set to 1 (default), the
TACH count decreases linearly and the fan speed increases with
temperature. At temperature T
X
, the fan runs at FS
X
and speed
increases with temperature to FS
X+1
at temperature T
X+1
.
Alternatively, the fan can be run at discrete fan speeds. When
discrete/linear speed (Bit 2) is set to 0, the fan runs at a new
speed once the temperature threshold is exceeded.
SELECTING WHICH TEMPERATURE CHANNEL
CONTROLS A FAN
Fan Behavior Register (Address 0x07)
Bits <1:0> = DRIVE Behavior
The ADM1033 can be configured so that either the local
temperature or the remote temperature controls the fan.
In default, the remote temperature controls the fan.
Table 30. Drive BHVR Bits
Bits
Drive x BHVR
00
Local Temperature Controls the Fan
01
Remote Temperature Controls the Fan
10
Remote Temperature Controls the Fan
11
Fan Runs at Full Speed
LOOK-UP TABLE HYSTERESIS
The user can program a hysteresis to be applied to the look-up
table. The advantage of this is apparent, if the temperature is
cycling around one of the threshold temperatures, particularly
when the look-up table is configured in discrete mode. It is not
as important in linear mode.
Table 31. Programming the Hysteresis
Code
0000 0000
0000 0001
0000 0010
0000 0101
0000 1000
0000 1111
Hysteresis Value
0°C
1°C
2°C
5°C
8°C
15°C
The hysteresis register of the look-up table is at Address 0x3A.
A hysteresis value of between 0°C and 15°C can be
programmed with a resolution of 1°C and applied to all the
temperature thresholds. Table 31 gives sample values for
programming.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1033ARQZ-REEL7 | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1041ARQ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ | Secondary-Side Controller with Current Share and Housekeeping |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1033ARQZ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1033ARQZ-RL7 | 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1034ARQ | 制造商:ON Semiconductor 功能描述:Temp Sensor Digital Serial (2-Wire) 16-Pin QSOP Tube 制造商:Rochester Electronics LLC 功能描述:DUAL FAN CONTROLLER, SRC, SMBUS I.C. - Bulk |
| ADM1034ARQ-REEL | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。