欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADM1033ARQZ-RL7
廠商: ON Semiconductor
文件頁數: 22/35頁
文件大小: 424K
描述: IC THERM/FAN SPEED CTLR 16-QSOP
產品變化通告: MFG CHG Notification ADI to ON Semi
Product Discontinuation 30/Sept/2011
標準包裝: 1,000
功能: 風扇控制,溫度監控器
傳感器類型: 內部和外部
感應溫度: -40°C ~ 125°C,外部傳感器
精確度: ±1°C
拓撲: ADC,比較器,多路復用器,寄存器庫
輸出類型: SMBus?
輸出警報:
輸出風扇:
電源電壓: 3 V ~ 3.6 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 16-QSOP
包裝: 帶卷 (TR)
ADM1033
http://onsemi.com
22
R1 and R2 should be chosen such that
(eq. 3)
2V t V
PULLUP
  R2(R
PULLUP
) R1 ) R2) t 5 V
The fan inputs have an input resistance of nominally
160 kW to ground. This should be taken into account when
calculating resistor values.
With a pullup voltage of 12 V and pullup resistor less than
1 kW, suitable values for R1 and R2 would be 100 kW and
47 kW. This gives a high input voltage of 3.83 V.
Figure 37. Fan with Strong TACH. Pullup to >V
CC
 or
Totem-Pole Output, Clamped with Zener and Resistor
12 V
V
CC
FAN SPEED
COUNTER
FAN (07)
ADM1033
*CHOOSE ZD1 VOLTAGE APPROXIMATELY 0.8 ?V
CC
PULL-UP
TYP < 1 kW
OR TOTEM-POLE
ZD1*
Figure 38. Fan with Strong TACH. Pullup to >V
CC
 or
Totem-Pole Output, Attenuated with R1/R2
12 V
V
CC
FAN SPEED
COUNTER
FAN (07)
ADM1033
*SEE TEXT
< 1 kW
R1*
R2
TACH
OUTPUT
Fan Speed Measurement
The fan counter does not count the fan TACH output
pulses directly. This is because the fan may be spinning at
less than 1000 rpm and it would take several seconds to
accumulate a reasonably large and accurate count. Instead,
the period of the fan revolution is measured by gating an
on-chip 81.92 kHz oscillator into the input of a 16-bit
counter for one complete revolution of the fan. Therefore,
the accumulated count is actually proportional to the fan
tachometer period and inversely proportional to the fan
speed.
The number of poles in the fan must be programmed in
Configuration Register 3 (Address 0x03). Bits <3:0> set the
number of poles for Fan 1, and Bits <7:4> set the number of
poles for Fan 2. This number must be an even number only,
because there cannot be an uneven number of poles in a fan.
A TACH period is output for every two poles. Therefore, the
number of poles must be known so that the ADM1033 can
measure for a full revolution.
Figure 39 shows the fan speed measurement period,
assuming that the fan outputs an ideal TACH signal. In
reality, the TACH signal output by the fan is chopped by the
drive signal. However, since the drive and the TACH signal
are synchronized, there is enough information available for
the ADM1033 to measure the fan speed accurately.
Figure 39. Fan Speed Measurement for a 4-pole Fan
CLOCK
IDEAL
TACH
FAN
MEASUREMENT
PERIOD
Fan Speed Measurement Registers
These 16-bit measurements are stored in the TACH value
registers.
Table 26. TACH VALUE REGISTERS
Register
Description
Default
0x4A
TACH1 Period, LSB
0xFF
0x4B
TACH1 Period, MSB
0xFF
0x4C
TACH2 Period, LSB
0xFF
0x4D
TACH2 Period, MSB
0xFF
Reading Fan Speed
Reading back fan speeds involves a 2-register read for
each measurement. The low byte should be read first. This
freezes the high byte until both high and low byte registers
have   been   read,   preventing   erroneous   fan   speed
measurement readings.
The fan tachometer reading registers report back the
number of 12.2 ms period clocks (81.92 kHz oscillator)
gated to the fan speed counter, for one full rotation of the fan,
assuming the correct number of poles is programmed. Since
the ADM1033 essentially measures the fan TACH period,
the higher the count value, the slower the actual fan speed.
A 16-bit fan TACH reading of 0xFFFF indicates that the fan
has stalled or is running very slowly (< 75 rpm).
Calculating Fan Speed
Fan speed in rpm is calculated as follows. This assumes
that the number of poles programmed in the Configuration
Register 3 (Address 0x03) is correct for both fans.
Fan Speed (RPM) = (81920 ?60)/Fan TACH Reading
where:
Fan TACH Reading = 16-bit Fan TACHometer Reading
Example:
TACH1 High Byte (Reg. 0x4A) = 0x17
TACH1 Low Byte (Reg. 0x4B) = 0xFF
What is Fan 1 speed in rpm?
Fan 1 TACH Reading = 0x17FF = 6143d
RPM = (f ?60) / Fan 1 TACH reading
相關PDF資料
PDF描述
ADM1034ARQZ-REEL IC THERM/FAN SPEED CTRLR 16-QSOP
ADN8810ACPZ-REEL7 IC CURRENT SOURCE(12BIT) 24LFCSP
ADP2140ACPZ3328R7 IC REG DL BCK/LINEAR 10LFCSP
ADP5022ACBZ-6-R7 IC REG TRPL BCK/LINEAR 16WLCSP
ADP5041ACPZ-1-R7 IC REG TRPL BCK/LINEAR 20-LFCSP
相關代理商/技術參數
參數描述
ADM1034 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Thermal Monitor and Fan Speed (RPM) Controller
ADM1034ARQ 制造商:ON Semiconductor 功能描述:Temp Sensor Digital Serial (2-Wire) 16-Pin QSOP Tube 制造商:Rochester Electronics LLC 功能描述:DUAL FAN CONTROLLER, SRC, SMBUS I.C. - Bulk
ADM1034ARQ-REEL 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1034ARQ-REEL7 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1034ARQZ 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
主站蜘蛛池模板: 闽侯县| 莆田市| 天水市| 繁昌县| 镶黄旗| 湘潭市| 鹿邑县| 景德镇市| 景东| 汪清县| 博野县| 甘泉县| 蓝田县| 洛阳市| 安吉县| 盈江县| 富顺县| 开阳县| 五河县| 衡阳县| 塔城市| 岑巩县| 兴化市| 澎湖县| 曲松县| 砀山县| 丹寨县| 黄龙县| 布拖县| 昌宁县| 保亭| 万安县| 浦县| 中西区| 和龙市| 封丘县| 浙江省| 大兴区| 攀枝花市| 沅江市| 汤阴县|