欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADM1066ASU
廠商: ANALOG DEVICES INC
元件分類: 電源管理
英文描述: Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs
中文描述: 10-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48
封裝: 7 X 7 MM, PLASTIC, MS-026ABC, TQFP-48
文件頁數: 14/32頁
文件大小: 861K
代理商: ADM1066ASU
ADM1066
INPUT COMPARATOR HYSTERESIS
The UV and OV comparators shown in Figure 22 are always
looking at VPn. To avoid chattering (multiple transitions when
the input is very close to the set threshold level), these compara-
tors have digitally programmable hysteresis. The hysteresis can
be programmed up to the values shown in Table 5.
Rev. 0 | Page 14 of 32
The hysteresis is added after a supply voltage goes out of
tolerance. Therefore, the user can program how much above
the UV threshold the input must rise again before a UV fault is
deasserted. Similarly, the user can program how much below the
OV threshold an input must fall again before an OV fault is
deasserted.
The hysteresis figure is given by
V
HYST
=
V
R
×
N
THRESH
/255
where:
V
HYST
is the desired hysteresis voltage.
N
THRESH
is the decimal value of the 5-bit hysteresis code.
Note that
N
THRESH
has a maximum value of 31. The maximum
hysteresis for the ranges is listed in Table 5.
INPUT GLITCH FILTERING
The final stage of the SFDs is a glitch filter. This block provides
time-domain filtering on the output of the SFD comparators.
This allows the user to remove any spurious transitions such as
supply bounce at turn-on. The glitch filter function is additional
to the digitally programmable hysteresis of the SFD compara-
tors. The glitch filter timeout is programmable up to 100 μs.
For example, when the glitch filter timeout is 100 μs, any pulses
appearing on the input of the glitch filter block that are less than
100 μs in duration are prevented from appearing on the output
of the glitch filter block. Any input pulse that is longer than
100 μs does appear on the output of the glitch filter block. The
output is delayed with respect to the input by 100 μs. The
filtering process is shown in Figure 23.
0
T
0
T
GF
T
0
T
GF
T
0
T
GF
T
0
T
GF
INPUT
INPUT PULSE SHORTER
THAN GLITCH FILTER TIMEOUT
INPUT PULSE LONGER
THAN GLITCH FILTER TIMEOUT
OUTPUT
PROGRAMMED
TIMEOUT
PROGRAMMED
TIMEOUT
INPUT
OUTPUT
Figure 23. Input Glitch Filter Function
SUPPLY SUPERVISION WITH VXn INPUTS
The VXn inputs have two functions. They can be used as either
supply fault detectors or digital logic inputs. When selected as an
analog (SFD) input, the VXn pins have very similar functionality
to the VH and VPn pins. The major difference is that the VXn
pins have only one input range: 0.573 V to 1.375 V. Therefore,
these inputs can directly supervise only the very low supplies.
However, the input impedance of the VXn pins is high, allowing
an external resistor divide network to be connected to the pin.
Thus, any supply can be potentially divided down into the input
range of the VXn pin and supervised. This enables the ADM1066
to monitor other supplies such as +24 V, +48 V, and 5 V.
An additional supply supervision function is available when the
VXn pins are selected as digital inputs. In this case, the analog
function is available as a second detector on each of the dedi-
cated analog inputs, VP1–4 and VH. The analog function of
VX1 is mapped to VP1, VX2 is mapped to VP2, and so on. VX5
is mapped to VH. In this case, these SFDs can be viewed as a
secondary or warning SFD.
The secondary SFDs are fixed to the same input range as the
primary SFD. They are used to indicate warning levels rather
than failure levels. This allows faults and warnings to be gener-
ated on a single supply using only one pin. For example, if VP1
is set to output a fault if a 3.3 V supply droops to 3.0 V, VX1 can
be set to output a warning at 3.1 V. Warning outputs are available
for readback from the status registers. They are also OR’ed
together and fed into the sequencing engine (SE), allowing
warnings to generate interrupts on the PDOs. Therefore, in the
example above, if the supply droops to 3.1 V, a warning is
generated, and remedial action can be taken before the supply
drops out of tolerance.
相關PDF資料
PDF描述
ADM1069 SUPER SEQUENCER-TM WITH MARGINING CONTROL AND AUXILIARY ADC INPUTS
ADM1069ACP SUPER SEQUENCER-TM WITH MARGINING CONTROL AND AUXILIARY ADC INPUTS
ADM1069ACP-REEL SUPER SEQUENCER-TM WITH MARGINING CONTROL AND AUXILIARY ADC INPUTS
ADM1069ACP-REEL7 SUPER SEQUENCER-TM WITH MARGINING CONTROL AND AUXILIARY ADC INPUTS
ADM1070 -48 V Hot Swap Controller
相關代理商/技術參數
參數描述
ADM1066ASU-REEL 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 48-Pin TQFP T/R
ADM1066ASU-REEL7 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 48-Pin TQFP T/R
ADM1066ASU-U3 制造商:AD 制造商全稱:Analog Devices 功能描述:Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs
ADM1066ASUZ 功能描述:IC SUPERVISOR/SEQUENCER 48-TQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 其它有關文件:STM6905 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:5 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 140 ms 電壓 - 閥值:2.188V,2.955V,可調,可調,可調 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-TSSOP 包裝:Digi-Reel® 產品目錄頁面:1197 (CN2011-ZH PDF) 其它名稱:497-8728-6
ADM1066ASUZ-REEL 功能描述:IC SEQUENCER/SUPERVISOR 48TQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP(0.059",1.50mm 寬)5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT
主站蜘蛛池模板: 旌德县| 依兰县| 灵宝市| 梅州市| 福泉市| 桐柏县| 南丹县| 宜川县| 麻栗坡县| 凤庆县| 湖北省| 新巴尔虎右旗| 米易县| 梁山县| 忻州市| 尉犁县| 吉水县| 凤翔县| 海门市| 雷州市| 阿瓦提县| 夏津县| 阿勒泰市| 青岛市| 四川省| 贵港市| 榕江县| 嘉黎县| 肃北| 永胜县| 班戈县| 乡城县| 皮山县| 普安县| 海南省| 五大连池市| 华安县| 广平县| 理塘县| 清流县| 共和县|