- 您現在的位置：買賣IC網 > PDF目錄373996 > ADM1069ACP-REEL (Analog Devices, Inc.) SUPER SEQUENCER-TM WITH MARGINING CONTROL AND AUXILIARY ADC INPUTS PDF資料下載
參數資料
| 型號： | ADM1069ACP-REEL |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | SUPER SEQUENCER-TM WITH MARGINING CONTROL AND AUXILIARY ADC INPUTS |
| 中文描述： | 超時序與裕度控制以及輔助ADC輸入商標 |
| 文件頁數： | 29/32頁 |
| 文件大小： | 626K |
| 代理商： | ADM1069ACP-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁
Preliminary Technical Data
ADM1069
5.
Rev. PrB | Page 29 of 32
The slave asserts ACK on SDA.
6.
The master sends a data byte that tells the slave device how
many data bytes are being sent. The SMBus specification
allows a maximum of 32 data bytes in a block write.
7.
The slave asserts ACK on SDA.
8.
The master sends N data bytes.
9.
The slave asserts ACK on SDA after each data byte.
10.
The master asserts a stop condition on SDA to end the
transaction.
0
ASLAVE
S
W A
2
(BLOCK WRITE)
4
1
3
A
5
BYTE
6
A
7
A
9
10
A
P
A
D1
8
DN
D2
Figure 43. Block Write to EEPROM or RAM
Unlike some EEPROM devices that limit block writes to within
a page boundary, there is no limitation on the start address
when performing a block write to EEPROM, except
There must be at least N locations from the start address to
the highest EEPROM address (0xFBFF), to avoid writing to
invalid addresses.
If the addresses cross a page boundary, both pages must be
erased before programming.
Note that the ADM1069 features a clock extend function for
writes to EEPROM. Programming an EEPROM byte takes
approximately 250 μs, which would limit the SMBus clock for
repeated or block write operations. The ADM1069 pulls SCL
low and extends the clock pulse when it cannot accept any
more data.
READ OPERATIONS
The ADM1069 uses the following SMBus read protocols.
Receive Byte
In a receive byte operation, the master device receives a single
byte from a slave device, as follows:
1.
The master device asserts a start condition on SDA.
2.
The master sends the 7-bit slave address followed by the
read bit (high).
3.
The addressed slave device asserts ACK on SDA.
4.
The master receives a data byte.
5.
The master asserts no acknowledge on SDA.
6.
The master asserts a stop condition on SDA, and the
transaction ends.
In the ADM1069, the receive byte protocol is used to read a
single byte of data from a RAM or EEPROM location whose
address has previously been set by a send byte or write
byte/word operation, as shown in Figure 44.
0
2
3
1
4
5
SLAVE
ADDRESS
S
R
DATA
P
A
6
A
Figure 44. Single Byte Read from EEPROM or RAM
Block Read
In a block read operation, the master device reads a block of
data from a slave device. The start address for a block read must
have been set previously. In the ADM1069, this is done by a
send byte operation to set a RAM address, or a write byte/word
operation to set an EEPROM address. The block read operation
itself consists of a send byte operation that sends a block read
command to the slave, immediately followed by a repeated start
and a read operation that reads out multiple data bytes, as
follows:
1.
The master device asserts a start condition on SDA.
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts ACK on SDA.
4.
The master sends a command code that tells the slave
device to expect a block read. The ADM1069 command
code for a block read is 0xFD (1111 1101).
5.
The slave asserts ACK on SDA.
6.
The master asserts a repeat start condition on SDA.
7.
The master sends the 7-bit slave address followed by the
read bit (high).
8.
The slave asserts ACK on SDA.
9.
The ADM1069 sends a byte-count data byte that tells the
master how many data bytes to expect. The ADM1069
always returns 32 data bytes (0x20), which is the maximum
allowed by the SMBus 1.1 specification.
10.
The master asserts ACK on SDA.
11.
The master receives 32 data bytes.
12.
The master asserts ACK on SDA after each data byte.
13.
The master asserts a stop condition on SDA to end the
transaction.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1069ACP-REEL7 | SUPER SEQUENCER-TM WITH MARGINING CONTROL AND AUXILIARY ADC INPUTS |
| ADM1070 | -48 V Hot Swap Controller |
| ADM1070ART | -48 V Hot Swap Controller |
| ADM1072ARQ | Dual, USB 2.0 Full/Standby Power Controller with Supply Steering |
| ADM1085 | Simple Sequencers in 6-Lead SC70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1069ACP-REEL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:SUPER SEQUENCER-TM WITH MARGINING CONTROL AND AUXILIARY ADC INPUTS |
| ADM1069ACPZ | 功能描述:IC SUPERVISOR/SEQ PROG 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 其它有關文件:STM6717 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:2 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:1.11V，3.075V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 產品目錄頁面:1194 (CN2011-ZH PDF) 其它名稱:497-7019-6 |
| ADM1069ACPZ-REEL | 功能描述:IC SUPERVISOR/SEQ PROG 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| ADM1069ACPZ-REEL7 | 功能描述:IC SUPERVISOR/SEQ PROG 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| ADM1069ARTZ | 制造商:Analog Devices 功能描述:SUPER SEQUENCER - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。