- 您現在的位置：買賣IC網 > PDF目錄373999 > ADM1181 (Analog Devices, Inc.) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | ADM1181 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | RS-232 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | 5V的高速RS - 232收發器與0.1uF電容 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 163K |
| 代理商： | ADM1181 |
ADM202E/ADM1181A
–9–
REV. 0
IE C1000-4-3 RADIAT E D IMMUNIT Y
IEC1000-4-3 (previously IEC801-3) describes the measurement
method and defines the levels of immunity to radiated electro-
magnetic fields. It was originally intended to simulate the elec-
tromagnetic fields generated by portable radio transceivers or
any other device which generates continuous wave radiated
electromagnetic energy. Its scope has since been broadened to
include spurious EM energy which can be radiated from fluores-
cent lights, thyristor drives, inductive loads, etc.
T esting for immunity involves irradiating the device with an EM
field. T here are various methods of achieving this including use
of anechoic chamber, stripline cell, T EM cell, GT EM cell. A
stripline cell consists of two parallel plates with an electric field
developed between them. T he device under test is placed within
the cell and exposed to the electric field. T here are three severity
levels having field strengths ranging from 1 V to 10 V/m. Results
are classified in a similar fashion to those for IEC1000-4-2.
1. Normal Operation.
2. T emporary Degradation or loss of function that is self-
recoverable when the interfering signal is removed.
3. T emporary degradation or loss of function that requires
operator intervention or system reset when the interfering
signal is removed.
4. Degradation or loss of function that is not recoverable due to
damage.
T he ADM202E/ADM1181A products easily meet Classification
1 at the most stringent (Level 3) requirement. In fact field
strengths up to 30 V/m showed no performance degradation,
and error-free data transmission continued even during irradia-
tion.
T able III. T est Severity Levels (IE C1000-4-3)
Level
Field Strength V/m
1
2
3
1
3
10
E MISSIONS/INT E RFE RE NC E
EN55 022, CISPR22 defines the permitted limits of radiated
and conducted interference from Information T echnology (IT )
equipment. T he objective of the standard is to minimize the
level of emissions both conducted and radiated.
For ease of measurement and analysis, conducted emissions are
assumed to predominate below 30 MHz and radiated emissions
are assumed to predominate above 30 MHz.
CONDUCT E D E MISSIONS
T his is a measure of noise that gets conducted onto the mains
power supply. Switching transients from the charge pump that
are 20 V in magnitude and contain significant energy can lead to
conducted emissions. Other sources of conducted emissions can
be due to overlap in switch on-times in the charge pump voltage
converter. In the voltage doubler shown below, if S2 has not
fully turned off before S4 turns on, this results in a transient
current glitch between V
CC
and GND which results in con-
ducted emissions. It is, therefore, important that the switches in
the charge pump guarantee break-before-make switching under
all conditions so that instantaneous short circuit conditions do
not occur.
T he ADM202E has been designed to minimize the switching
transients and ensure break-before-make switching thereby
minimizing conducted emissions. T his has resulted in the level
of emissions being well below the limits required by the specifi-
cation. No additional filtering/decoupling other than the recom-
mended 0.1
μ
F capacitor is required.
Conducted emissions are measured by monitoring the mains
line. T he equipment used consists of a LISN (Line Impedance
Stabilizing Network) that essentially presents a fixed impedance
at RF, and a spectrum analyzer. T he spectrum analyzer scans
for emissions up to 30 MHz and a plot for the ADM202E is
shown in Figure 19.
S1
S2
C1
S4
S3
C3
V+ = 2V
CC
V
CC
INTERNAL
OSCILLATOR
GND
V
CC
Figure 17. Charge Pump Voltage Doubler
1
2
SWITCHING GLITCHES
Figure 18. Switching Glitches
LOG FREQUENCY – MHz
80
70
0
0.3
30
0.6
1
60
50
10
40
30
20
3
6
10
d
LIMIT
Figure 19. ADM202E Conducted Emissions Plot
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1181A | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ADM202EAN | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ADM202EARN | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ADM202EARU | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ADM1181AAN | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1181A | 制造商:AD 制造商全稱:Analog Devices 功能描述:EMI/EMC Compliant, +-15 kV ESD Protected, RS-232 Line Drivers/Receivers |
| ADM1181AAN | 功能描述:IC TXRX RS-232 5V 15KV 16DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM1181AANZ | 功能描述:IC TXRX RS-232 5V 15KV 16-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM1181AARW | 功能描述:IC TXRX RS-232 5V 15KV 16SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM1181AARW-REEL | 制造商:Analog Devices 功能描述:Dual Transmitter/Receiver RS-232 16-Pin SOIC W T/R |
發布緊急采購，3分鐘左右您將得到回復。