- 您現在的位置：買賣IC網 > PDF目錄374016 > ADN2819 (Analog Devices, Inc.) Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp PDF資料下載
參數資料
| 型號： | ADN2819 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| 中文描述： | 多速率為2.7 Gb / s的集成時鐘和數據恢復芯片限幅放大器 |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 570K |
| 代理商： | ADN2819 |
ADN2819
LOS RESPONSE TIME
The LOS response time is the delay between the removal of the
input signal and indication of loss of signal (LOS) at SDOUT.
The ADN2819’s response time is 300 ns typ when the inputs are
dc-coupled. In practice, the time constant of ac-coupling at the
quantizer input determines the LOS response time.
Rev. B | Page 10 of 24
JITTER SPECIFICATIONS
The ADN2819 CDR is designed to achieve the best bit-error-
rate (BER) performance, and has exceeded the jitter transfer,
generation, and tolerance specifications proposed for
SONET/SDH equipment defined in the Telcordia Technologies
specification.
Jitter is the dynamic displacement of digital signal edges from
their long-term average positions measured in UI (unit
intervals), where 1 UI = 1 bit period. Jitter on the input data
can cause dynamic phase errors on the recovered clock
sampling edge. Jitter on the recovered clock causes jitter on the
retimed data.
The following sections summarize the specifications of the jitter
generation, transfer, and tolerance in accordance with the
Telcordia document (GR-253-CORE, Issue 3, September 2000)
for the optical interface at the equipment level, and the
ADN2819 performance with respect to those specifications.
Jitter Generation
Jitter generation specification limits the amount of jitter that
can be generated by the device with no jitter and wander
applied at the input. For OC-48 devices, the band-pass filter has
a 12 kHz high-pass cutoff frequency, with a roll-off of
20 dB/decade and a low-pass cutoff frequency of at least
20 MHz. The jitter generated should be less than 0.01 UI rms
and 0.1 UI p-p.
Jitter Transfer
Jitter transfer function is the ratio of the jitter on the output
signal to the jitter applied on the input signal versus the
frequency. This parameter measures the limited amount of jitter
on an input signal that can be transferred to the output signal
(see Figure 11).
SLOPE = –20dB/DECADE
JITTER FREQUENCY (kHz)
0.1
J
f
C
ACCEPTABLE
RANGE
0
Figure 11. Jitter Transfer Curve
Jitter Tolerance
Jitter tolerance is defined as the peak-to-peak amplitude of the
sinusoidal jitter applied on the input signal that causes a 1 dB
power penalty. This is a stress test that is intended to ensure no
additional penalty is incurred under the operating conditions
(see Figure 12). Figure 13 shows the typical OC-48 jitter
tolerance performance of the ADN2819.
SLOPE = –20dB/DECADE
f
0
f
1
f
2
f
3
f
4
JITTER FREQUENCY (Hz)
15
1.5
0.15
I
0
Figure 12. SONET Jitter Tolerance Mask
MODULATION FREQUENCY (Hz)
10
1k
100k
10M
100
10
0.1
A
1
100
10k
1M
1
ADN2819
OC-48 SONET MASK
0
Figure 13. OC-48 Jitter Tolerance Curve
相關PDF資料 |
PDF描述 |
|---|---|
| ADN2819ACP-CML | Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2819ACP-CML-RL | Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2819ACPZ-CML-RL1 | Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2819ACPZ-CML1 | Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2830ACP32-REEL | Circular Connector; No. of Contacts:4; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:21; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:21-75 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADN2819ACP-CML | 制造商:Analog Devices 功能描述:CDR 2488.32Mbps/2666.06Mbps SONET/SDH 48-Pin LFCSP EP Tray 制造商:Rochester Electronics LLC 功能描述:MULTI-RATE 2.7GBPS CDR/ PA LOW POWER I.C - Bulk |
| ADN2819ACP-CML-RL | 制造商:Analog Devices 功能描述:CDR 2488.32Mbps/2666.06Mbps SONET/SDH 48-Pin LFCSP EP T/R |
| ADN2819ACPZ-CML | 功能描述:IC CLOCK/DATA RECOVERY 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ADN2819ACPZ-CML1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2819ACPZ-CML-RL | 功能描述:IC CLOCK/DATA RECOVERY 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。