- 您現在的位置：買賣IC網 > PDF目錄374019 > ADP1610ARMZ-R7 (ANALOG DEVICES INC) 1.2 MHz DC-DC Step-Up Switching Converter PDF資料下載
參數資料
| 型號： | ADP1610ARMZ-R7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.2 MHz DC-DC Step-Up Switching Converter |
| 中文描述： | 2 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | LEAD FREE, MO-187AA, MSOP-8 |
| 文件頁數： | 10/16頁 |
| 文件大小： | 948K |
| 代理商： | ADP1610ARMZ-R7 |
ADP1610
THEORY OF OPERATION
The ADP1610 current-mode step-up switching converter
converts a 2.5 V to 5.5 V input voltage up to an output voltage as
high as 12 V. The 1.2 A internal switch allows a high output
current, and the high 1.2 MHz switching frequency allows tiny
external components. The switch current is monitored on a
pulse-by-pulse basis to limit it to 2 A.
Rev. 0 | Page 10 of 16
CURRENT-MODE PWM OPERATION
The ADP1610 uses current-mode architecture to regulate the
output voltage. The output voltage is monitored at FB through a
resistive voltage divider. The voltage at FB is compared to the
internal 1.23 V reference by the internal transconductance error
amplifier to create an error current at COMP. A series resistor-
capacitor at COMP converts the error current to a voltage. The
switch current is internally measured and added to the stabiliz-
ing ramp, and the resulting sum is compared to the error
voltage at COMP to control the PWM modulator. This current-
mode regulation system allows fast transient response, while
maintaining a stable output voltage. By selecting the proper
resistor-capacitor network from COMP to GND, the regulator
response is optimized for a wide range of input voltages, output
voltages, and load conditions.
FREQUENCY SELECTION
The ADP1610’s frequency is user-selectable to operate at either
700 kHz to optimize the regulator for high efficiency or to
1.2 MHz for small external components. Connect RT to IN for
1.2 MHz operation, or connect RT to GND for 700 kHz
operation. To achieve the maximum duty cycle, which might be
required for converting a low input voltage to a high output
voltage, use the lower 700 kHz switching frequency.
SOFT START
To prevent input inrush current at startup, connect a capacitor
from SS to GND to set the soft start period. When the ADP1610
is in shutdown (SD is at GND) or the input voltage is below the
2.4 V undervoltage lockout voltage, SS is internally shorted to
GND to discharge the soft start capacitor. Once the ADP1610 is
turned on, SS sources 3 μA to the soft start capacitor at startup.
As the soft start capacitor charges, it limits the voltage at COMP.
Because of the current-mode regulator, the voltage at COMP is
proportional to the switch peak current, and, therefore, the
input current. By slowly charging the soft start capacitor, the
input current ramps slowly to prevent it from overshooting
excessively at startup.
ON/OFF CONTROL
The SD input turns the ADP1610 regulator on or off. Drive SD
low to turn off the regulator and reduce the input current to
10 nA. Drive SD high to turn on the regulator.
When the dc-dc step-up switching converter is turned off, there
is a dc path from the input to the output through the inductor
and output rectifier. This causes the output voltage to remain
slightly below the input voltage by the forward voltage of the
rectifier, preventing the output voltage from dropping to zero
when the regulator is shut down. Figure 28 shows the applica-
tion circuit to disconnect the output voltage from the input
voltage at shutdown.
SETTING THE OUTPUT VOLTAGE
The ADP1610 features an adjustable output voltage range of V
IN
to 12 V. The output voltage is set by the resistive voltage divider
(R1 and R2 in Figure 2) from the output voltage (V
OUT
) to the
1.230 V feedback input at FB. Use the following formula to
determine the output voltage:
V
OUT
= 1.23 × (1 +
R1
/
R2
)
(1)
Use an R2 resistance of 10 k or less to prevent output voltage
errors due to the 10 nA FB input bias current. Choose R1 based
on the following formula:
R1
=
R2
×
23
.
23
.
OUT
V
(2)
INDUCTOR SELECTION
The inductor is an essential part of the step-up switching
converter. It stores energy during the on-time, and transfers that
energy to the output through the output rectifier during the off-
time. Use inductance in the range of 1 μH to 22 μH. In general,
lower inductance values have higher saturation current and
lower series resistance for a given physical size. However, lower
inductance results in higher peak current that can lead to
reduced efficiency and greater input and/or output ripple and
noise. Peak-to-peak inductor ripple current at close to 30% of
the maximum dc input current typically yields an optimal
compromise.
For determining the inductor ripple current, the input (V
IN
) and
output (V
OUT
) voltages determine the switch duty cycle (D) by
the following equation:
D
=
OUT
V
IN
OUT
V
V
(3)
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3000AR-33 | Circular Connector Cable Assembly; Connector Type A:Circular Plug; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes |
| ADP3000 | Isolated Flyback Switching Regulator with 9V Output |
| ADP3000AN | Isolated Flyback Switching Regulator with 9V Output |
| ADP3000AN-3.3 | Voltage-Mode SMPS Controller |
| ADP3000AR-3.3 | Voltage-Mode SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP1610-BL1-EVZ | 制造商:Analog Devices 功能描述:Evaluation Board For Step-Up DC-DC Converter 制造商:Analog Devices 功能描述:BLANK ADISIMPOWER EVAL ADP1610 - Boxed Product (Development Kits) |
| ADP1610-EVALZ | 功能描述:BOARD EVALUATION FOR ADP1610 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓撲結構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
| ADP1611 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Constant-Frequency, Current-Mode Step-Up DC/DC Controller |
| ADP1611ARMZ-R7 | 功能描述:IC REG BOOST ADJ 1.2A 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| ADP1611-EVAL | 制造商:AD 制造商全稱:Analog Devices 功能描述:20 V,1.2 MHz Step-Up DC-to-DC Switching Converter |
發布緊急采購，3分鐘左右您將得到回復。