- 您現在的位置：買賣IC網 > PDF目錄374019 > ADP3050AR-5 (ANALOG DEVICES INC) Circular Connector Cable Assembly; Connector Type A:Circular Receptacle; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | ADP3050AR-5 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Circular Connector Cable Assembly; Connector Type A:Circular Receptacle; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes |
| 中文描述： | 2.1 A SWITCHING REGULATOR, 240 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | MS-012AA, SOIC-8 |
| 文件頁數： | 16/16頁 |
| 文件大小： | 191K |
| 代理商： | ADP3050AR-5 |
–
16
–
C
–
2
–
3
P
ADP3050
REV. 0
The largest peak currents occur at the lowest input voltage. For
this design with a load current of 500 mA:
I
A
PEAK
=
+
12
×
+
×
=
12
5
0 5
.
1
2
0 375
.
0.
The average current diode will be equal to the load current.
An inductor with a current rating 20% greater than 0.9 A should
be used (rating of at least 1.2 A). Inductors and diodes with ratings
greater than 1 A should always be used, even if the calculated peak
and average currents are lower. This will ensure that start-up and
fault conditions will not overstress the components.
For the buck-boost topology, the input voltage can be less than
the output voltage (i.e., V
IN
= 4 V, V
OUT
=
–
5 V), but the avail-
able load current will be even lower. The equations given in this
section are valid for input voltages less than and greater than the
output voltage. The voltage seen by the ADP3050 is equal to the
sum of the input and output voltages (the BOOST pin sees the
sum of V
IN
+ 2 |V
OUT
|). Make sure that the maximum voltage
ratings of these pins are not exceeded.
Dual Output SEPIC Regulator
For many systems, a dual polarity supply is needed. The circuit
in Figure 28 generates both a positive and a negative 5 V output
using a single magnetic component. The two inductors shown
are actually two separate windings on a single core contained in
a small, surface-mount package. The windings can be connected
in parallel or in series to be used as a single inductor for a con-
ventional buck regulator, or they can be used as a 1:1 transformer,
as in this application. One winding is used as the standard buck
inductor for the +5 V output. The second winding is used to
generate the
–
5 V output along with D2, C6, and C7.
U1
ADP3050-5
V
IN
1
2
3
4
SWITCH
BOOST
BIAS
FB
IN
GND
SD
COMP
8
7
6
5
C3
0.22 F
D1
1N5818
GND
12V
C1
22 F
+
C2
0.01 F
L1*
25 H
V
OUT
+5V @ 0.5A
R1
5.1k
C4
1nF
D3
1N4148
+C5
100 F
SD
*INDUCTOR IS A SINGLE CORE
WITH TWO WINDINGS
COILTRONICS CTX25-4
5V @ 0.25A
V
OUT
+
C6
100 F
L1*
25 H
+C7
100 F
D2
1N5818
Figure 28. Dual Output +5 V and
–
5 V Regulator
These components form a SEPIC (Single Ended Primary Induc-
tance Converter) using the 1:1 coupled inductor to generate the
negative supply. When the switch is off, the voltage across the buck
winding is equal to V
O
+ V
D
(V
D
is the diode drop). This voltage is
generated across the second winding, which is connected to produce
the
–
5 V supply. The
–
5 V output would be generated even
without C6 in the circuit, but its inclusion greatly improves the
regulation of the negative output and lowers the inductor ripple
current. The total output current available for both supplies is
limited by the ADP3050 (internally limited to around 1.0 A).
Keeping load currents below 500 mA and 250 mA, for the posi-
tive and negative supplies, respectively, will ensure that current
limit is not reached under normal operation. These limits are
not interchangeable; 500 mA cannot be drawn from the
–
5 V
supply while drawing only 250 mA from the +5 V supply. The
maximum current available from the
–
5 V output is directly related
to the +5 V load current due to the fact that the +5 V output is
used to regulate both supplies. Typically, the
–
5 V load current
should be around one-half of the +5 V load current to ensure good
regulation of both outputs. Additionally, the
–
5 V output should
have a preload (the minimum current level) of 1% to 2% of the
+5 V load current. This will help maintain good regulation of the
–
5 V output at light loads.
The ripple voltage of the +5 V output is that of a normal buck
regulator (as described in the Applications Information section).
This ripple voltage is determined by the inductor ripple current
and the ESR of the output capacitor. For the system below, the
positive output voltage ripple is a 30 mV peak-to-peak triangular
wave. The ripple voltage of the
–
5 V output is a rectangular
wave (due to the rectangular shape of the current waveform into
the
–
5 V output capacitor). The amplitude of this current wave-
form is approximately equal to twice the
–
5 V load current. For
a load current of 200 mA and an ESR of 100 m
, the negative
output voltage ripple is around 2 200 mA 100 m
, or
about 40 mV. The edges of this ripple waveform are quite fast,
which, along with the inductance of the output capacitor, generates
narrow spikes on the negative output voltage. These spikes can
easily be filtered out using an additional 5
μ
F to 10
μ
F bypass
capacitor close to the load (the inductance of the PC board
trace and the additional capacitor create a low-pass filter to
remove these high frequency spikes).
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead SOIC
(R Suffix)
0.1968 (5.00)
0.1890 (4.80)
8
5
4
1
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.1574 (4.00)
0.1497 (3.80)
0.0688 (1.75)
0.0532 (1.35)
SEATING
PLANE
0.0098 (0.25)
0.0040 (0.10)
0.0192 (0.49)
0.0138 (0.35)
0.0500
(1.27)
BSC
0.0098 (0.25)
0.0075 (0.19)
0.0500 (1.27)
0.0160 (0.41)
8
°
0
°
0.0196 (0.50)
°
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3050 | 200 kHz, 1 A High-Voltage Step-Down Switching Regulator |
| ADP3050AR | 200 kHz, 1 A High-Voltage Step-Down Switching Regulator |
| ADP3155 | 5-Bit Programmable Triple Power Supply Controller for Pentium III Processors |
| ADP3155JRU | 5-Bit Programmable Triple Power Supply Controller for Pentium III Processors |
| ADP3156JR-15 | Dual Power Supply Controller for Desktop Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP3050AR-5-REEL | 制造商:Analog Devices 功能描述:Conv DC-DC Single Step Down 3.6V to 30V 8-Pin SOIC N T/R |
| ADP3050AR-5-REEL7 | 制造商:Analog Devices 功能描述:Conv DC-DC Single Step Down 3.6V to 30V 8-Pin SOIC N T/R 制造商:Analog Devices 功能描述:ANAADP3050AR-5-REEL7 HI VOLT SWCH REG |
| ADP3050AR-REEL | 制造商:Analog Devices 功能描述:Conv DC-DC Single Step Down 3.6V to 30V 8-Pin SOIC N T/R |
| ADP3050AR-REEL7 | 制造商:Analog Devices 功能描述:Conv DC-DC Single Step Down 3.6V to 30V 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| ADP3050ARZ | 功能描述:IC REG BUCK ADJ 1A 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
發布緊急采購，3分鐘左右您將得到回復。